Need help?Do you have a question about the Thermo Scientific 310 and is the answer not in the manual?
General| Brand | Thermo Scientific |
|---|---|
| Model | 310 |
| Category | Accessories |
| Language | English |
Explains the control panel interface, buttons, and display elements.
Details how to navigate and operate the incubator using the keypad.
Describes the information shown on the incubator's digital displays.
Provides instructions for physically placing and setting up the incubator.
Guides on how to safely stack multiple incubator units.
Outlines initial cleaning procedures before using the incubator.
Instructions for correctly positioning the incubator shelves.
Details the installation of the access port filter.
Procedure for installing the optional HEPA filter.
Steps for connecting the air sample filter assembly.
Instructions for ensuring the incubator is level for proper operation.
Essential steps for safely connecting the incubator to a power source.
Guidance on filling the humidity pan with appropriate water.
Procedures for safely connecting the CO2 gas supply.
Steps to initiate the incubator after installation and connection.
How to set the desired operating temperature for the incubator.
Instructions for configuring the over-temperature safety setpoint.
Guide on how to set the target CO2 concentration.
Procedure for calibrating the incubator's temperature control.
Steps to calibrate the thermal conductivity CO2 sensor system.
Instructions for calibrating the infrared CO2 sensor system.
Guide on how to calibrate the relative humidity sensor.
How to enable or disable the audible alarm function.
Steps to set a passcode for controlling access to settings.
Configuring the threshold for the low temperature alarm.
Setting up the low temperature alarm to trigger external contacts.
Configuring the threshold for the low CO2 concentration alarm.
Configuring the threshold for the high CO2 concentration alarm.
Setting up CO2 alarms to trigger external contacts.
Inputting new zero calibration numbers for T/C CO2 sensors.
Inputting new span calibration numbers for T/C CO2 sensors.
Configuring the threshold for the low relative humidity alarm.
Setting up RH alarms to trigger external contacts.
Configuring which parameters (Temp/RH) are shown on the display.
Choosing the primary gas supply tank for the Gas Guard system.
Instructions for turning off the Gas Guard system if not in use.
Setting the unique address for RS485 communication.
Describes the alarm for failure in temperature control.
Details alarms indicating a problem with any of the unit's sensors.
Indicates an error with the CO2 sensor or its connections.
Alarm for errors during the automatic zero calibration of IR CO2 sensors.
Step-by-step guide for cleaning and disinfecting the incubator's interior.
Instructions for cleaning the outside of the incubator unit.
Procedures for cleaning the incubator's glass doors.
How to clean the pan that maintains humidity.
Guide on how to change the direction of the incubator door swing.
Information on replacing the HEPA filter.
Steps for safely replacing the incubator's power fuses.
Overview of the incubator's main internal components.
Details regarding the incubator's electronic components.
Instructions for replacing the sample air filter.
How to connect external alarm systems to the incubator.
Instructions for connecting the incubator via RS485.
Guide for connecting analog output boards for data logging.
Information about the built-in CO2 Gas Guard system.
How the CO2 Gas Guard system functions and its alarms.
Details about the optional humidity monitoring feature.
Factors influencing humidity levels within the incubator.
Information on the accuracy of the humidity readout sensor.
How to connect an uninterruptible power supply (UPS).
Specific connection steps for a 115V UPS.
Specific connection steps for a 230V UPS.
Technical specifications for temperature control and range.
Safety features related to temperature monitoring and control.
Specifications for relative humidity control and display.
Technical specifications for CO2 control, sensor, and range.
Dimensions and construction details of the incubator shelves.
Details on the incubator's interior and exterior construction materials.
Specifications for the various ports and fittings on the unit.
Electrical requirements, voltage, current, and outlet specifications.
Thermal output specification of the incubator.
Overall exterior and interior physical dimensions.
Net weight of the incubator in different configurations.
List of available optional features and accessories.
Details on available upgrades with copper components.
Specifications for optional analog and digital data output signals.
Information regarding product certifications and compliance.
Environmental and safety requirements for operation.
Details the terms and conditions of the USA warranty for the incubator.
To Next Page