Toro Reelmaster 5100-D - Output Test: Speed Out of Range Signal

________________________________________________________________________________________
______ ___ ______ ___ ______ ___ ______ __ ______ ___ ______ ___ ______ ___ ___ __ ___ ______ ___ _____ ___ ______ ___ ______
______ ___ ______ ___ ______ ___ ______ __ ______ ___ ______ ___ ______ ___ ___ __ ___ ______ ___ _____ ___ ______ ___ ______
______ ___ ______ ___ ______ ___ ______ __ ______ ___ ______ ___ ______ ___ ___ __ ___ ______ ___ _____ ___ ______ ___ ______
______ ___ ______ ___ ______ ___ ______ __ ______ ___ ______ ___ ______ ___ ___ __ ___ ______ ___ _____ ___ ______ ___ ______
______ ___ ______ ___ ______ ___ ______ __ ______ ___ ______ ___ ______ ___ ___ __ ___ ______ ___ _____ ___ ______ ___ ______
______ ___ ______ ___ ______ ___ ______ __ ______ ___ ______ ___ ______ ___ ___ __ ___ ______ ___ _____ ___ ______ ___ ______
__
__ __ __ __ __ __
__ __ __ __ __ __
__ __ __ __ __ __
__ __ __ __ __ __
__ __ __ __ __ __
__ __ __ __ __ __
Engine (cont.)
Item
Piston
Type
Material
Piston Outside Diameter (skirt end)
Piston to Cylinder Wall Clearance
Oversize
Protrusion from cylinder
block top surface
__ __ __ __ __ __ _
Piston Pin
Type
Outside Diameter
Pin to Piston Clearance
Pin to Connecting Rod Clearance
__ __ __ __ __ __ _
Piston Rings
Number of Rings
2 Compression
1 Oil
Compression Ring Width
Oil Ring Width
Compression Ring Side Clearance (No. 2)
Oil Ring Side Clearance
Ring Gap
__ __ __ __ __ __ _
Connecting Rod
Type
Bend and Twist
Big End Thrust Clearance
__ __ __ __ __ __ _
Connecting Rod Bearings
Oil Clearance
Undersize
__ __ __ __ __ __ _
Crankshaft
Type
Bend
End Play
Journal O.D.
Pin O.D.
Finish Undersize
Journal U.S. 0.25 mm (0.01 in.)
Journal U.S. 0.50 mm (0.02 in.)
Pin U.S. 0.25 mm (0.01 in.)
Pin U.S. 0.50 mm (0.02 in.)
__ __ __ __ __ __ _
Main Bearings
Oil Clearance
Undersize
Standard Specification
Solid
Aluminum alloy
76 mm (2.99 in.)
0.25, 0.50 mm
(0.01, 0.02 in.)
0.9 mm (0.035 in.)
__ __ __ __ _
Semi-floating
18 mm (0.709 in.)
Press-fit load: 1000
+ 500 kg
(2200
+ 1100 lb.)
__ __ __ __ _
No. 1: Chrome plated, semi-keystone type
No. 2: Tapered
Chrome plated ring with coil expander
2 mm (0.079 in.)
3 mm (0.118 in.)
0.05 - 0.09 mm (0.002 - 0.004 in.)
0.03 - 0.07 mm (0.001 - 0.003 in.)
0.15 - 0.40 mm (0.006 - 0.016 in.)
__ __ __ __ _
Forged I-beam
Within 0.05 mm (0.002 in.)
0.1 - 0.35 mm (0.004 - 0.014 in.)
__ __ __ __ _
0.25, 0.50 mm
(0.01, 0.02 in.)
__ __ __ __ _
Fully counterbalanced
Within 0.03 mm (0.001 in.)
0.05 - 0.175 mm (0.002 - 0.007 in.)
43 mm (1.693 in.)
40 mm (1.575 in.)
42.715 - 42.730 mm
(1.6817 - 1.6823 in.)
42.465 - 42.480 mm
(1.6719 - 1.6724 in.)
39.715 - 39.730 mm
(1.5636 - 1.5642 in.)
39.465 - 39.480 mm
(1.5537 - 1.5543 in.)
__ __ __ __ _
0.25, 0.50 mm
(0.01, 0.02 in.)
Repair Limit
__ __
__ __
__ __
__ __
__ __
– 0.15 mm (– 0.006 in.)
– 0.15 mm (– 0.006 in.)
__ __
Service Limit
0.3 mm (0.012 in.)
___ __ __ __ ___
0.08 mm (0.003 in.)
___ __ __ __ ___
0.2 mm (0.008 in.)
0.2 mm (0.008 in.)
1.5 mm (.060 in.)
___ __ __ __ ___
0.15 mm (0.006 in.) max.
0.5 mm (0.02 in.)
___ __ __ __ ___
0.15 mm (0.006 in.)
___ __ __ __ ___
0.05 mm (0.002 in.)
– 0.70 mm (– 0.028 .in)
– 0.70 mm (– 0.028 .in)
___ __ __ __ ___
0.10 mm (0.004 in.)
Specifications Page 3 - 6
Rev. A
Reelmaster
®
223-D/5100-D