Toro Reelmaster 5100-D - Output Test: Backlap Solenoids S8;S9

_________________________________________________________________________________________
___ ______ ___ ______ ___ ______ ___ __ ___ ___ ______ ___ ______ ___ ______ ___ ______ ___ ______ ______ ___ ______ ___
___ ______ ___ ______ ___ ______ ___ __ ___ ___ ______ ___ ______ ___ ______ ___ ______ ___ ______ ______ ___ ______ ___
_________________________________________________________________________________________
___ ______ ___ ______ ___ ______ ___ __ ___ ___ ______ ___ ______ ___ ______ ___ ______ ___ ______ ______ ___ ______ ___
___ ______ ___ ______ ___ ______ ___ __ ___ ___ ______ ___ ______ ___ ______ ___ ______ ___ ______ ______ ___ ______ ___
___ ______ ___ ______ ___ ______ ___ __ ___ ___ ______ ___ ______ ___ ______ ___ ______ ___ ______ ______ ___ ______ ___
___ ______ ___ ______ ___ ______ ___ __ ___ ___ ______ ___ ______ ___ ______ ___ ______ ___ ______ ______ ___ ______ ___
__
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _____ __ __ __ ____
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _____ __ __ __ ____
__
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _____ __ __ __ ____
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _____ __ __ __ ____
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _____ __ __ __ ____
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ _____ __ __ __ ____
Engine (cont.)
Item
Camshafts
Drive System
Front Journal
Journal to Cylinder Block Hole Clearance
Cam Lobe Major Diameter
(both intake and exhaust)
Cam Lobe Major Diameter (pump cam)
Tappets
Outside Diameter
Tappet to Cylinder Block Hole Clearance
Push Rod Bend
Standard Specification
Gear
Ball bearing
27.37 mm (1.078 in.)
30 mm (1.224 in.)
_ _
19 mm (0.748 in.)
_ _
Within 0.3 mm (0.012 in.)
Repair Limit
_ _
_ _
Service Limit
0.15 mm (0.006 in.)
– 1.0 mm (– 0.0433 in.)
– 0.7 mm (– 0.028 in.)
_
0.15 mm (0.006 in.)
_
Lubrication System
Item
Oil Capacity
API Service Class
Viscosity
Above 68
o
F (20
o
C)
41
o
F to 68
o
F (5
o
to 20
o
C)
Below 41
o
F (5
o
C)
Oil Pump
Type
Check Valve Opening Pressure
Outer Rotor to Housing Clearance
Outer Rotor Thrust Clearance
Oil Pressure Switch
Indicator Lamp Lighting Pressure
Standard Specification
3.6 liter (3.8 qt.)
including oil filter
_ _
CD
_ _
SAE 30 or 10W-30
SAE 20 or 10W-30
SAE 10W-30
_ _
Gear type
3 ± 0.3 kg/cm
2
(42.66 ± 4.27 lb/in
2
)
at 1000 rpm
0.100 - 0.196 mm (0.004 - 0.008 in.)
0.04 - 0.10 mm (0.002 - 0.004 in.)
_ _
7.1 lbs/in
2
(0.5 kg/cm
2
)
Repair Limit
_ _
_ _
_ _
0.3 mm (0.012 in.)
0.25 mm (0.01 in.)
_ _
Service Limit
_
_
_
_
Reelmaster
®
223-D/5100-D Page 3 - 7 Specifications