Toshiba Tosvert VF-S15 User Manual

E6582175
17
■ Parameters changed default setting values
Table 1 : Parameter list changed default setting values at software V120 or later version
Title
Com.
No
Function Unit
Minimum
setting unit
Panel/Com.
Adjustment
range
Default
setting
Reference
*2
vb
0016 Torque boost value 1 % 0.1 / 0.1 0.0 - 30.0 *1 6.4
f172
0172 Torque boost value 2 % 0.1 / 0.1 0.0 - 30.0 *1 6.8.1
f402
0402 Automatic torque boost value % 0.1 / 0.1 0.1 - 30.0 *1 6.25
f415
0415 Motor rated current A 0.01 / 0.01 0.10 - 100.00 *1
f416
0416 Motor no-load current % 1 / 1 10 - 90 *1
f417
0417 Motor rated speed min
-1
1 / 1 100 - 64000 *1
f456
0456 Motor specific constant 12 - 1 / 1 20 - 150 120 -
f457
0457 Motor specific constant 13 - 1 / 1 5 - 75 50 -
f458
0458 Motor specific constant 2 - 1 / 1 0 - 101 101 -
f459
0459 Load inertia moment ratio Times 0.1 / 0.1 0.1 - 100.0 1.5 6.25
*1: Default setting values are different depending on the inverter ratings. (Refer to Table 3.)
*2: Refer to section 11.2 to 11.5.
■ Default setting, region setting
Regarding the change of the parameter default setting values described on Table 1, the several functions described below are
changed from V120 or later version.
Table 2 : Function changed at V120 or later version inverter
Item Before (V116 or earlier version) After (V120 or later version) Reference
50Hz default setting
(typ=1)
Function is not changed.
f417(Motor rated speed): 1410(min
-1
) is set. It is NOT dependent on the inverter ratings.
4.3.2
60Hz default setting
(typ=2)
Function is not changed.
f417(Motor rated speed): 1710(min
-1
) is set. It is NOT dependent on the inverter ratings.
Default setting 1
(typ=3)
Parameters on Table 1 are initialized to the
values described on Table 4.
Parameters on Table1 are initialized to the
values described on Table 3.
Default setting 2
(typ=13)
Parameters on Table 1 are initialized to the
values described on Table 4.
(Region setting is required in advance)
Parameters on Table 1 are initialized to the
values described on Table 3.
(Region setting is required in advance)
Region setting
(set)
Parameters on Table 1 are initialized to the
values described on Table 4.
Parameters on Table 1 are initialized to the
values described on Table 3.
4.4
11.5
(f456 and f457 do not exist on V110 or earlier version inverter.)
S-3

Toshiba Tosvert VF-S15 Specifications

General

Category	Inverter
Control Method	V/f control, Sensorless vector control
Cooling Method	Forced air cooling
Model	Tosvert VF-S15
Protection Features	Overcurrent, Overvoltage, Undervoltage, Overheat
Communication Options	Modbus RTU
Overload Capacity	150% for 1 minute
Braking Unit	Built-in braking transistor
Output Voltage	3-Phase, same as input voltage
Operating Temperature	-10 to +50°C (14 to 122°F)
Storage Temperature	-20 to 65°C (-4 to 149°F)
Humidity	5 to 95% RH (non-condensing)
Altitude	Up to 1000m above sea level
Input Voltage	3-Phase 200 to 240 VAC, 3-Phase 380 to 480 VAC
Weight	Varies depending on model (e.g., 0.8 kg to 16 kg)