Woodward GCP-30 Series - Table 3-1: Event Recorder - Messages, Part 1

Manual 37278B GCP-30 Series - Genset Control
© Woodward Page 19/174
Event type xxxxxxxxxxxxxxxx
German English
Internal events
Engine overspeed (Pickup)
Überdrehzahl
Over speed
Generator overfrequency
Überfrequenz
Overfrequency
Generator underfrequency
Unterfrequenz
Underfrequency
Generator overvoltage
Gen.-Überspg.
Gen.overvolt.
Generator undervoltage
Gen.-Unterspg.
Gen.undervolt.
Generator overcurrent, level 1
Gen.-Überstrom 1
Gen.overcurr. 1
Generator overcurrent, level 2
Gen.-Überstrom 2
Gen.overcurr. 2
Reverse/reduced load
Rück/Minderleist
Revers/min.power
Overload
Gen.-Überlast
Gen.overload
Unbalanced load
Schieflast
Load unbalance
Mains overvoltage
Netz-Überspg.
Mains-overvolt.
Mains undervoltage
Netz-Unterspg.
Mains-undervolt.
Mains overfrequency
Netz-Überfreq.
Mains-underfreq.
Mains underfrequency
Netz-Unterfreq.
Mains-overfreq.
Mains phase/vector jump
Phasensprung
Phase shift
Mains df/dt (optional)
df/dt-Fehler
df/dt error
Battery undervoltage
Batt.-Unterspg.
Batt.undervolt.
GCB synchronization time monitoring
Synch.Zeit GLS
GCB syn.failure
MCB synchronization time monitoring
Synch.Zeit NLS
MCB syn.failure
Switching to dead busbar time monitoring
Stör. df/dU-max.
Failure df/dVmax
Fault P-control: GCB will be opened after time boost/settle
R-Rampe:GLS auf
P-ramp:open GCB
GCB malfunction on closing
Störung GLS ZU
GCBclose failure
MCB malfunction on closing
Störung NLS ZU
MCBclose failure
GCB malfunction on opening
Störung GLS AUF
GCB open failure
MCB malfunction on opening
Störung NLS AUF
mCB open failure
Faulty reference power zero control with interchange synchronization on GCB
Bezugsleist. <>0
Power not zero
Maintenance call
Wartung
Service
Interface monitoring X1-X5
Fehl.Schnit.X1X5
Interf.err. X1X5
Interface monitoring Y1-Y5
Fehl.Schnit.Y1Y5
Interf.err. Y1Y5
Pickup/generator frequency mismatch
Pickup/Gen.Freq.
Pickup/Gen.freq.
Plausibilty control power (optional)
L.-Plausibilität
Plausibility ch.
Shutdown malfunction
Abstellstörung
Stop failure
Start failure
Fehlstart
Start failure
Unintentional stop
ungewollter Stop
unintended stop
Discrete Inputs in the GCP/AMG
Discrete input [D01]
frei parametrierbar freely configurable
Discrete input [D02]
Discrete input [D03]
Discrete input [D04]
Discrete input [D05]
Discrete input [D06]
Discrete input [D07]
Discrete input [D08]
Discrete input [D09]
Discrete input [D10]
Discrete input [D11]
Discrete input [D12]
Discrete input [D13]
Discrete input [D14]
Discrete input [D15]
Discrete input [D16]
Table 3-1: Event recorder - Messages, part 1