EasyManuals Logo

Xerox WorkCentre 3119 Service Manual

Xerox WorkCentre 3119
185 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #129 background imageLoading...
Page #129 background image
General Procedures and Information
WorkCentre 3119 06/06 6-19
Cleaning Voltage (THV-)
- The (+) Transfer Voltage is not outputted because the THV PWM is controlled with high.
- The (-) Transfer Voltage is outputted because the THV-Enable Signal is controlled with
low
- The output fluctuation range is big because there is no Feedback control.
- Input Voltage : 24 V DC 15%
- Output Voltage : -1KV 15%
- Output Voltage Rising Time : 100 ms Max
- Output Voltage Falling Time : 100 ms Max
Developing Voltage (DEV)
- Input Voltage : 24 V DC 15%
- Output Voltage: -200V to -600V DC 3%
- Output Voltage Fluctuation range: PWM Control
- Input contrast of the output stability degree : 3 % or less
Loading contrast : 3 % or less
- Output Voltage Rising Time : 50 ms Max
- Output Voltage Falling Time : 50 ms Max
- Output Loading range : 10M - 1000 M
- Output Control Signal (BIAS-PWM) : the CPU output is HV output when PWM is low.
Supply
- Output Voltage : -400 V to -800V DC 5%(ZENER using, DEV )
- Input contrast of the output stability degree : under 3 %
Loading contrast : 5 % or less
- Output Voltage Rising Time: 50 ms Max
- Output Voltage Falling Time: 50 ms Max
- Output Loading Range: 10 M - 1000 M
- Output Control Signal (BIAS-PWM): the CPU is HV output when PWM is low.
3. SMPS (Switching Mode Power Supply)
•AC Input
- Input Rated Voltage: AC 220V - 240V AC 110V - 127V
- Input Voltage fluctuating Range: AC 198V - 264V AC 99V - 135V
- Rated Frequency: 50/60 Hz
- Frequency Fluctuating Range: 47 - 63 Hz
- Input Current: Under 5.0Arms / 2.5Arms (But, the status when lamp is off or rated voltage
is inputted/outputted )
Rated Output Power
Table 1:
No Item CH1 CH2 CH3 Remark
1 Channel Name +5V +24V +24.0VS
2 Connector Pin CON2
5V Pin 3,4,24
GND Pin 5,6
CON2
24V Pin 13
GND Pin 7,9,10
CON2
24VS PIN 11, 12
GND Pin 7,9,10
3 Rated Output +5V +/-5%
(4.75-5.25V)
+24V+/-15%
(21.6-27.6)
+24V+/-15%
(21.6-27.6)
4 Max. Current Output 1.0A 0.5A 1.0A

Table of Contents

Other manuals for Xerox WorkCentre 3119

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Xerox WorkCentre 3119 and is the answer not in the manual?

Xerox WorkCentre 3119 Specifications

General IconGeneral
Print TechnologyLaser
Print Speed19 ppm
Print Resolution600 x 600 dpi
Copy Speed19 cpm
Copy Resolution600 x 600 dpi
Paper Capacity250 sheets
ConnectivityUSB 2.0
FunctionsPrint, Copy, Scan
Scanner TypeFlatbed
Memory (Standard)32 MB
Operating System CompatibilityWindows, Mac

Related product manuals