Xerox WorkCentre 4150

January 2016
2-35
WorkCentre 4150/4250/4260WorkCentre WorkCentre 4150/4250/42604150/
05-600, 05-700
Status Indicator RAPs
• Document transport assembly, PL 5.30 Item 26.
4265 Checkout
Refer to Wiring Diagram 45. Perform the following:
1. Open the DADF top cover assembly, PL 5.60. Remove all jammed paper.
2. Raise the DADF input tray, PL 5.60. Remove all jammed paper.
3. Check the document path for damage or obstructions.
4. Check that the following actuators move freely and are not damaged:
• Document detect sensor actuator, PL 5.65.
• Paper width sensor actuator, PL 5.65.
• Paper length sensor actuator, PL 5.65.
• Registration sensor actuator, PL 5.65.
5. Enter dC330. Check the following sensors. Install new components as necessary:
• Code 05-100, document detect sensor (Q05-100), PL 5.65.
• Code 05-110, paper width sensor (Q05-110), PL 5.65.
• Code 05-120, paper length sensor (Q05-120), PL 5.65.
• Code 05-130, registration sensor (Q05-130), PL 5.65.
6. Check the following wiring:
• Between the document detect sensor, and CN7 on the DADF PWB.
• Between the paper width sensor and CN7 on the DADF PWB.
• Between the paper length sensor and CN9 on the DADF PWB.
• Between the registration sensor and CN5 on the DADF PWB.
7. If necessary, install new components:
• DADF PWB, PL 5.60.
• Document transport assembly, PL 5.60..
05-700 DADF Jam 7 RAP
05-700 The machine has detected that a oversize document has been fed.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 4150 Checkout
• 4250/4260 Checkout
• 4265 Checkout
4150 Checkout
Refer to Wiring Diagram 11. Perform the following:
1. Open the DADF top cover assembly, PL 5.15 Item 11. Remove all jammed paper.
2. Raise the DADF input tray, PL 5.10 Item 5. Remove all jammed paper.
3. Check that the customer is not attempting to feed documents outside of specification,
refer to GP 8 DADF Document Feeding Specifications.
4. Check the feed roll assembly, PL 5.15 Item 5. If necessary, install a new feed roll assem-
bly, PL 5.15 Item 5.
5. Check the retard pad, PL 5.20 Item 12. If necessary, install a new retard pad, PL 5.20
Item 12.
6. Check that the registration sensor actuator, PL 5.15 Item 12 moves freely and is not dam-
aged.
7. Enter dC330 code 05-130. Check the registration sensor (Q05-130), PL 5.15 Item 14.
8. Check the wiring between the registration sensor and CN5 on the DADF Sensor PWB. If
necessary, install a new registration sensor, PL 5.15 Item 14.
9. If necessary, install new components:
• DADF PWB, PL 5.20 Item 6.
• DADF sensor PWB, PL 5.20 Item 4.
• Document transport assembly, PL 5.10 Item 2.
4250/4260 Checkout
Refer to Wiring Diagram 29. Perform the following:
1. Open the DADF top cover assembly, PL 5.30 Item 2. Remove all jammed paper.
2. Raise the DADF input tray, PL 5.30 Item 11. Remove all jammed paper.
3. Check that the customer is not attempting to feed documents outside of specification,
refer to GP 8 DADF Document Feeding Specifications.
4. Check the feed roll assembly, PL 5.40 Item 7. If necessary, install a new feed roll assem-
bly, PL 5.40 Item 7.
5. Check the retard pad, PL 5.45 Item 4. If necessary, install a new retard pad, PL 5.45 Item
4.
6. Check that the registration sensor actuator, PL 5.40 Item 18 moves freely and is not dam-
aged.
7. Enter dC330 code 05-130. Check the registration sensor (Q05-130), PL 5.40 Item 17.