Xerox WorkCentre 4150

January 2016
2-36
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
05-700, 05-800
Status Indicator RAPs
8. Check the wiring between the registration sensor and CN7 on the DADF PWB. If neces-
sary, install a new registration sensor, PL 5.40 Item 17.
9. If necessary, install new components:
• DADF PWB, PL 5.30 Item 24.
• Document transport assembly, PL 5.30 Item 26.
4265 Checkout
Refer to Wiring Diagram 45. Perform the following:
1. Open the DADF top cover assembly, PL 5.60 . Remove all jammed paper.
2. Raise the DADF input tray, PL 5.60. Remove all jammed paper.
3. Check that the customer is not attempting to feed documents outside of specification,
refer to GP 8 DADF Document Feeding Specifications.
4. Check the feed roll assembly, PL 5.70. If necessary, install a new feed roll assembly, PL
5.40 Item 7.
5. Check the retard pad, PL 5.70. If necessary, install a new retard pad, PL 5.70.
6. Check that the registration sensor actuator, PL 5.65 moves freely and is not damaged.
7. Enter dC330 code 05-130. Check the registration sensor (Q05-130), PL 5.65.
8. Check the wiring between the registration sensor and CN5 on the DADF PWB. If neces-
sary, install a new registration sensor, PL 5.65.
9. If necessary, install new components:
• DADF PWB, PL 5.60.
• Document transport assembly, PL 5.60.
05-800 DADF Jam 8 RAP
05-800 The trail edge of the document failed to deactuate the R stack sensor within the correct
time in reverse mode.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Refer to Wiring Diagram 29. Perform the following:
1. Raise the DADF. Lower the lower inverter tray, PL 5.35 Item 3. Remove all jammed paper.
2. Check the document path for damage or obstructions.
3. Remove the jam clearance guide housing, PL 5.35 Item 15. Check the reverse guide, PL
5.35 Item 14 for damage.
4. Check that the following components are clean and rotate freely:
• Upper exit roll, PL 5.45 Item 20.
• Upper exit roll idlers, PL 5.55 Item 9.
• Lower exit roll, PL 5.55 Item 10.
• Lower exit roll idlers, PL 5.35 Item 8.
5. Check that the R stack sensor actuator, PL 5.35 Item 17 moves freely and is not dam-
aged.
6. Check the R stack sensor, PL 5.35 Item 16.
NOTE: There is not a component control code for the R stack sensor.
7. Check the wiring between the R stack sensor and CN12 on the DADF PWB. If necessary,
install a new R stack sensor, PL 5.35 Item 16.
8. Remove the DADF rear cover, PL 5.30 Item 13. Enter dC330 code 05-210. Check that the
DADF duplex motor, PL 5.30 Item 7 runs and drives the lower exit roll, PL 5.55 Item 10.
9. Check the wiring between the DADF duplex motor and CN11 on the DADF PWB.
10. If necessary, install new components:
• DADF duplex motor assembly, PL 5.30 Item 7.
• DADF PWB, PL 5.30 Item 24.
• Document transport assembly, PL 5.30 Item 26.
•DADF assembly, PL 5.30 Item 1.