Xerox WorkCentre 4150

January 2016
2-40
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
05A
Status Indicator RAPs
05A Document Not Sensed in DADF RAP
Use this RAP if the machine fails to detect a document in the DADF.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 4150 Checkout
• 4250/4260 Checkout
• 4265 Checkout
4150 Checkout
1. Refer to Wiring Diagram 11. Perform the following:
a. Check that the document detect sensor actuator, PL 5.20 Item 17 moves freely and
is not damaged. If necessary, install a document detect sensor actuator, PL 5.20
Item 17.
b. Enter dC330 code 05-100. Check the document detect sensor (Q05-100), PL 5.20
Item 13.
c. Check the wiring between the document detect sensor and CN4 on the DADF Sen-
sor PWB. If necessary, install a new document detect sensor, PL 5.20 Item 13.
d. Check the wiring between CN1 on the DADF Sensor PWB and CN3 on the DADF
PWB.
2. Refer to Wiring Diagram 9. Perform the following:
a. Check that the platen cover sensor actuator, PL 14.10 Item 12 moves freely and is
not damaged.
b. Enter dC330 code 05-400. Check the platen cover sensor (Q05-400), PL 14.10 Item
14.
c. Check the wiring between the platen cover sensor and CN3 on the Scanner PWB. If
necessary, install a new platen cover sensor, PL 14.10 Item 12.
4250/4260 Checkout
1. Refer to Wiring Diagram 29. Perform the following:
a. Check that the document detect sensor actuator, PL 5.45 Item 15 moves freely and
is not damaged. If necessary, install a document detect sensor actuator, PL 5.45
Item 14.
b. Enter dC330 code 05-100. Check the document detect sensor (Q05-100), PL 5.45
Item 10.
c. Check the wiring between the document detect sensor and CN3 on the DADF PWB.
If necessary, install a new document detect sensor, PL 5.45 Item 10.
2. Refer to Wiring Diagram 28. Perform the following:
a. Check that the platen cover sensor actuator, PL 14.13 Item 27 moves freely and is
not damaged.
b. Enter dC330 code 05-400. Check the platen cover sensor (Q05-400), PL 14.13 Item
14.
c. Check the wiring between the platen cover sensor and CN4 on the Scanner PWB. If
necessary, install a new platen cover sensor, PL 14.13 Item 14.
4265 Checkout
1. Refer to Wiring Diagram 45. Perform the following:
a. Check that the document detect sensor actuator, PL 5.60 moves freely and is not
damaged. If necessary, install a document detect sensor actuator, PL 5.60.
b. Enter dC330 code 05-100. Check the document detect sensor (Q05-100), PL 5.60.
c. Check the wiring between the document detect sensor and CN3 on the DADF PWB.
If necessary, install a new document detect sensor, PL 5.60.
2. Refer to Wiring Diagram 44. Perform the following:
a. Check that the platen cover sensor actuator, PL 14.13 Item 27 moves freely and is
not damaged.
b. Enter dC330 code 05-400. Check the platen cover sensor (Q05-400), PL 14.13 Item
14.
c. Check the wiring between the platen cover sensor and CN4 on the Scanner PWB. If
necessary, install a new platen cover sensor, PL 14.13 Item 14.