Xerox WorkCentre 4150

January 2016
2-64
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
09-200
Status Indicator RAPs
4250/4260 Checkout
NOTE: The main PWB has 4 test points, GND, +3.3V, +5V and +24V. The location of the test
points is shown on the Main PWB PJ location illustration.
NOTE: The side cover assembly interlock switch must be closed to supply +24V to the motors
and clutches.
Refer to Wiring Diagram 23. Perform the following:
1. Make sure that the toner cartridge is not empty. If necessary, install a new toner cartridge,
PL 9.10 Item 2.
2. Enter dC330 code 09-600 and 09-700. Check that the toner dispense motor (MOT09-
600), PL 4.25 Item 3 runs and deactuates the toner sensor (Q09-700).
NOTE: It may be necessary to enter the codes several times to ensure that the toner dis-
pense motor deactuates the toner sensor. It may also be necessary to make several cop-
ies to prevent over toning the xerographic module.
3. Remove the toner cartridge, PL 9.10 Item 2 and xerographic module, PL 9.10 Item 1.
Enter dC330 code 09-600. Make sure that the toner dispense motor runs and drives the
toner dispense idler gear, PL 4.25 Item 7 and coupling, PL 4.25 Item 9. Install new com-
ponents as necessary, PL 4.25.
4. Check the wiring between the toner dispense motor and CN10 on the Main PWB.
5. Check the wiring between the xerographic module connector, PL 4.15 Item 35 and CN11
on the Main PWB. If necessary, install a new xerographic module connector, PL 4.15 Item
35.
6. If necessary, install a new xerographic module, PL 9.10 Item 1.
7. Perform the OF5 Main PWB Check RAP.
4265 Checkout
NOTE: The main PWB has 4 test points, GND, +3.3V, +5V and +24V. The location of the test
points is shown on the Main PWB PJ location illustration.
NOTE: The side cover assembly interlock switch must be closed to supply +24V to the motors
and clutches.
Refer to Wiring Diagram 39. Perform the following:
1. Make sure that the toner cartridge is not empty. If necessary, install a new toner cartridge,
PL 9.10 Item 2.
2. Enter dC330 code 09-600 and 09-700. Check that the toner dispense motor (MOT09-
600), PL 4.25 Item 3 runs and deactuates the toner sensor (Q09-700).
NOTE: It may be necessary to enter the codes several times to ensure that the toner dis-
pense motor deactuates the toner sensor. It may also be necessary to make several cop-
ies to prevent over toning the xerographic module.
3. Remove the toner cartridge, PL 9.10 Item 2 and xerographic module, PL 9.10 Item 1.
Enter dC330 code 09-600. Make sure that the toner dispense motor runs and drives the
toner dispense idler gear, PL 4.25 Item 7 and coupling, PL 4.25 Item 9. Install new com-
ponents as necessary, PL 4.25.
4. Check the wiring between the toner dispense motor and CN15 on the Main PWB.
5. Check the wiring between the xerographic module connector, PL 4.15 Item 35 and CN22
on the Main PWB. If necessary, install a new xerographic module connector, PL 4.15 Item
35.
6. If necessary, install a new xerographic module, PL 9.10 Item 1.
7. Perform the OF5 Main PWB Check RAP.