Xerox WorkCentre 4150

January 2016
2-14
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
03-410 to 03-452
Status Indicator RAPs
03-410 to 03-452 Paper Information Mismatch RAP
03-410 The machine has detected a tray 1 paper colour, type or size mismatch.
03-411 The machine has detected a tray 1 paper type mismatch during a print job.
03-412 The machine has detected a tray 1 paper size mismatch during a print job.
03-420 The machine has detected a tray 2 paper colour, type or size mismatch.
03-421 The machine has detected a tray 2 paper type mismatch during a print job.
03-422 The machine has detected a tray 2 paper size mismatch during a print job.
03-430 The machine has detected a tray 3 paper colour, type or size mismatch.
03-431 The machine has detected a tray 3 paper type mismatch during a print job.
03-432 The machine has detected a tray 3 paper size mismatch during a print job.
03-440 The machine has detected a tray 4 paper colour, type or size mismatch.
03-441 The machine has detected a tray 4 paper type mismatch during a print job.
03-442 The machine has detected a tray 4 paper size mismatch during a print job.
03-450 The machine has detected a bypass tray paper colour, type or size mismatch.
03-451 The machine has detected a bypass tray paper type mismatch during a print job.
03-452 The machine has detected a bypass tray paper size mismatch during a print job.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 4150 Checkout
• 4250/4260/4265 Checkout
4150 Checkout
NOTE: The main PWB has test points. The location of the test points is shown on the Main
PWB PJ location illustration.
Perform the following:
1. If the fault is present when printing, check that the print driver and machine tray informa-
tion are correct.
2. Go to GP 4 System Administration Tools. Check that the relevant tray paper type, colour
and size settings are correct.
3. 03-410, 411, 412 Only. Refer to Wiring Diagram 6. Perform the following:
a. Check the wiring between the paper size detect PWB, PL 7.15 Item 5 and CN15 on
the Main PWB.
b. Check the registration clutch, PL 4.15 Item 4. Ensure the clutch if held securely in
place by the KL-clip.
c. Install new components as necessary:
• Paper size detect PWB, PL 7.15 Item 5.
• Paper size detect assembly, PL 7.15 Item 1.
d. Perform the OF5 Main PWB Check RAP.
4. 03-420 to 03-442 Only. Refer to Wiring Diagram 7 and Wiring Diagram 13. Perform the
following:
a. Check the wiring between the paper size detect PWB, PL 7.20 Item 5 and CN5 on
the Tray PWB.
b. Check the wiring between CN1 on the relevant Tray PWB and CN24 on the Main
PWB.
c. Install new components as necessary:
• Paper size detect PWB, PL 7.20 Item 5.
• Paper size detect assembly, PL 7.20 Item 25.
• Tray connector, PL 7.20 Item 17.
d. Perform the OF5 Main PWB Check RAP.
4250/4260/4265 Checkout
NOTE: The main PWB has test points. The location of the test points is shown on the Main
PWB PJ location illustration.
Perform the following:
1. If the fault is present when printing, check that the print driver and machine tray informa-
tion are correct.
2. Go to GP 4 System Administration Tools. Check that the relevant tray paper type, colour
and size settings are correct.
3. 03-410, 411, 412 Only. Refer to Wiring Diagram 24. Perform the following:
a. Check the wiring between the paper size detect PWB, PL 7.15 Item 5 and CN14 on
the Main PWB.
b. Install new components as necessary:
• Paper size detect PWB, PL 7.15 Item 5.
• Paper size detect assembly, PL 7.15 Item 1.
c. Perform the OF5 Main PWB Check RAP.
4. 03-420 to 03-442 Only. (4252/4260) Refer to Wiring Diagram 13 and Wiring Diagram 24.
(Perform the following:
a. Check the wiring between the paper size detect PWB, PL 7.20 Item 5 and CN5 on
the Tray PWB.
b. Check the wiring between CN1 on the relevant Tray PWB and CN19 on the Main
PWB.
c. Install new components as necessary:
• Paper size detect PWB, PL 7.20 Item 5.
• Paper size detect assembly, PL 7.20 Item 25.
• Tray connector, PL 7.20 Item 17.
d. Perform the OF5 Main PWB Check RAP.