ABB ACS800-17LC - Dimensions, weights and free space requirements

Technical data
146
Definitions
Derating
The load capacity (current and power) decreases if the installation site altitude exceeds 1000 metres
(3281 ft), or if the ambient temperature exceeds +45 °C (+113 °F).
Temperature derating
In the temperature range +45 °C (+113 °F) to +55 °C (+131 °F), the rated output current is decreased
by 0.5% for every additional 1 °C (1.8 °F). The output current is calculated by multiplying the current
given in the rating table by the derating factor.
Example
If the ambient temperature is 55 °C (+131 °F), the derating factor is 100% - 0.5 · 10 °C =
95% or 0.95. The output current is then 0.95 × I
2N
or 0.95 × I
cont.max
.
U
N
= 690 V
ACS800-17LC-0130-7 106 137 110 102 90 79 75
ACS800-17LC-0170-7 139 206 132 133 132 104 90
ACS800-17LC-0210-7 179 265 200 172 160 134 132
ACS800-17LC-0280-7 237 386 250 228 200 177 160
ACS800-17LC-0390-7 330 604 315 317 315 247 250
ACS800-17LC-0470-7 395 604 400 379 355 295 250
ACS800-17LC-0630-7 530 872 560 509 500 396 400
ACS800-17LC-0950-7 795 1344 800 763 710 595 630
ACS800-17LC-1240-7 1040 1710 1000 998 1000 778 800
ACS800-17LC-1840-7 1540 2538 1600 1478 1400 1152 1200
ACS800-17LC-2430-7 2035 3350 2000 1954 2000 1522 1600
ACS800-17LC-3620-7 3025 4974 3200 2904 2800 2263 2400
ACS800-17LC-4630-7 3878 5802 4000 3723 3600 2901 2800
ACS800-17LC-5300-7 4432 6630 4400 4255 4000 3315 3200
ACS800-17LC-5960-7 4986 7460 5200 4787 4800 3730 3600
PDM 00430970
Nominal ratings
I
cont.max
Continuous rms output current. No overloadability at 45 °C (113 °F).
I
max
Maximum output current. Allowable for 10 seconds at start, otherwise as long as allowed
by drive temperature.
Typical ratings for no-overload use
P
cont.max
Typical motor power. The power ratings apply to most IEC 60034 motors at nominal voltage
(400, 500 or 690 V).
Typical ratings for light-overload use (10% overloadability)
I
2N
Continuous rms current. 10% overload is allowed for 1 minute every 5 minutes.
P
N
Typical motor power. The power ratings apply to most IEC 60034 motors at nominal voltage
(400, 500 or 690 V).
Typical ratings for heavy-duty use (50% overloadability)
I
2hd
Continuous rms current. 50% overload is allowed for 1 minute every 5 minutes.
P
hd
Typical motor power. The power ratings apply to most IEC 60034 motors at nominal voltage
(400, 500 or 690 V).
Drive type Nominal ratings No-overload
use
Light-overload use Heavy-duty use
I
cont.max
I
max
P
contmax
I
2N
P
N
I
2hd
P
hd
A (AC) A kW A kW A kW
%
°C