Why Agilent Technologies Water Pump shows shutdown?
The Agilent Technologies Water Pump may shut down due to several reasons: a leak detected in another module with a CAN connection (fix the leak before restarting), a leak or shut-down in an external instrument with a remote connection (check external instruments), or the degasser failing to generate sufficient vacuum (check the vacuum degasser for an error).
What to do if Agilent Technologies Water Pump shows Leak?
If you observe a leak in the Agilent Technologies Water Pump, check for loose fittings and tighten them. Also, inspect capillaries for breaks and replace them if needed. Ensure pump components are correctly seated, and if the leak persists, replace the appropriate seal, such as the active inlet valve or outlet ball valve. Finally, examine the pump seals and replace them if they are defective.
Why Agilent Technologies Water Pump displays Pressure Above Upper Limit?
If the Agilent Technologies Water Pump displays 'Pressure Above Upper Limit', it could be due to several reasons. The upper pressure limit might be set too low, so ensure it is suitable for the analysis. There might be a blockage in the flow path after the damper, so check for any obstructions. A defective damper or CSM board could also be the cause, requiring replacement.
What to do if Agilent Technologies Water Pump displays Pressure Below Lower Limit?
If the Agilent Technologies Water Pump indicates 'Pressure Below Lower Limit', it could be due to the lower pressure limit being set too high, so ensure it is appropriately set for the analysis. Air bubbles in the mobile phase can also cause this, so ensure solvents are degassed and purge the pump. A leak could be present, so inspect the pump head, capillaries, and fittings. Lastly, a defective damper or CSM board might be the cause, requiring replacement.
Why Agilent Technologies Water Pump shows Remote Time-out?
A 'Remote Time-out' error on the Agilent Technologies Water Pump may occur due to a not-ready condition in one of the connected instruments. Ensure the instrument is correctly installed and set up for analysis. A defective remote cable can also cause this issue, so try exchanging it. Finally, defective components in the instrument showing the not-ready condition may be the reason, so check the instrument for defects.
What causes Agilent Technologies Water Pump to display Leak Sensor Open?
The 'Leak Sensor Open' error on the Agilent Technologies Water Pump can be caused by: the leak sensor not being connected to the CSM board (ensure it is correctly connected), a defective leak sensor (exchange it), or the leak sensor being incorrectly routed and pinched by a metal component (ensure correct routing).
What to do if Agilent Technologies Water Pump displays Leak Sensor Short?
If the Agilent Technologies Water Pump displays a 'Leak Sensor Short' error, it could be due to a defective leak sensor, in which case you should replace it. It could also be caused by the leak sensor being incorrectly routed and pinched by a metal component, so try replacing the leak sensor.
How to fix Synchronization Lost on Agilent Technologies Water Pump?
To fix a 'Synchronization Lost' error on the Agilent Technologies Water Pump, first ensure all CAN cables are correctly connected. If the problem persists, switch off and restart the system to determine which module is not recognized. A defective CAN cable can also cause this, so try replacing it. Also check that all CAN cables are installed correctly.
What to do if Agilent Technologies Water Pump displays Fan Failed?
If the Agilent Technologies Water Pump displays a 'Fan Failed' error, ensure the fan is correctly connected. If it is, the fan may be defective and need replacement. A defective CSM board can also cause this, so consider replacing it. Also, make sure that cables or wires are not obstructing the fan blades.
Why Agilent Technologies Water Pump displays Missing Pressure Reading?
A 'Missing Pressure Reading' error on the Agilent Technologies Water Pump can occur if the damper is not connected, so ensure the damper connector is clean and correctly seated. Alternatively, the damper may be defective and need to be replaced. A defective CSM board may also cause this issue, requiring replacement.
General| Brand | Agilent Technologies |
|---|---|
| Model | 1100 Series |
| Category | Laboratory Equipment |
| Language | English |
Details on environmental conditions, power considerations, and power cords for detector operation.
Details on detection type, light source, wavelength range, noise, drift, and flow cell specifications.
Step-by-step instructions for physically installing the detector and connecting cables.
Procedures for connecting the flow cell capillaries and tubing to the detector.
Steps to note the MAC address and connect the instrument's LAN interface.
Details on IP address, Subnet Mask, and Default Gateway configuration methods.
Guidance on link speed/duplex settings and automatic configuration using Bootp.
Procedures for manual configuration using Telnet or a Handheld Controller.
Steps to configure the PC and Agilent ChemStation for LAN communication.
Steps for running samples, verifying results, and obtaining chromatograms.
Details on control, configuration, online spectra, analog outputs, spectrum, peakwidth, and slit settings.
Introduction to optimizing detector parameters for signal and spectral data.
Detailed explanation of the power supply and detector status indicators (green, yellow, red).
Essential safety warnings and precautions during maintenance and handling.
Step-by-step guide for replacing the deuterium or tungsten lamp.
Procedure for replacing the standard, semi-micro, or high-pressure flow cell.
Description of tests including intensity, wavelength calibration, and slit tests.
Comprehensive safety precautions for instrument operation, service, and repair.
To Next Page
