AMF-BRUNS K90 ACTIVE - User Manual

Questions and Answers

O
owensalexanderSep 9, 2025
Why is it not possible to operate AMF-BRUNS Cassette Lift using the Smartphone App?
- L
  Laura SimsSep 9, 2025
  There are several reasons why you might be unable to operate your AMF-BRUNS Cassette Lift using the Smartphone App: * First, check that the Bluetooth receiver is switched ON. Open the door above the cassette lift and ensure the switch is in the “ON” position. If there isn't a switch or the Bluetooth receiver has switched off, press the “Retract” button on the cable-connected remote control. * Second, make sure your smartphone is connected to the receiver. If not, connect it or reinstall the app. * Finally, if the Bluetooth control box is not installed, contact customer service.
E
Eric WatkinsSep 7, 2025
What to do if AMF-BRUNS Cassette Lift extends but does not raise or lower?
- D
  Drew LynchSep 8, 2025
  There are a few potential reasons why your AMF-BRUNS Cassette Lift platform might extend but not raise or lower: * The platform may not be fully extended because the vehicle is parked on an incline or the platform is obstructed. Try fully retracting the platform using the remote or app and then park the vehicle on level ground with enough space for full extension. * There may be an issue with the lift's electrical or hydraulic system. In this case, have the cassette lift checked by a specialist workshop.
R
Richard WareAug 22, 2025
What to do if AMF-BRUNS K90 ACTIVE Lifting Systems extends but does not raise or lower?
- J
  jblackAug 22, 2025
  If the platform of your AMF-BRUNS Back-in-Box-Lift extends but doesn't raise or lower, it might be because the platform isn't fully extended due to the vehicle being on an incline or an obstruction. Try retracting the platform using the cable-connected remote control, Bluetooth remote control, or Smartphone App, then park the vehicle on a level surface with sufficient space. If that doesn't work, the electrical or hydraulic system may be defective, and you should have it checked by a specialist workshop.
A
Alexis MillerSep 5, 2025
Why does AMF-BRUNS K90 ACTIVE Lifting Systems platform jerk when retracting?
- D
  Danielle ButlerSep 5, 2025
  If the platform jerks when retracting into the cassette on your AMF-BRUNS Back-in-Box-Lift, it might not be adjusted correctly. For K70 / K90 models, adjust the switching point for the retract position or adjust the rollers. For K90 ACTIVE models, adjust the switching point for the retract position.
J
Jeremiah JonesSep 4, 2025
How to troubleshoot AMF-BRUNS K90 ACTIVE Lifting Systems when the cable remote control doesn't work?
- R
  richard48Sep 4, 2025
  If you are unable to operate the AMF-BRUNS Lifting Systems using the cable-connected remote control, check the remote control and its connections. If it is defective, replace it.
C
crivasSep 3, 2025
Why AMF-BRUNS K90 ACTIVE lowers the platform slowly on its own?
- A
  Angela PettySep 3, 2025
  If your AMF-BRUNS Back-in-Box-Lift lowers the platform slowly on its own, the lowering valve might be defective and needs replacement by a specialist. Also, check if the ball-cock is open and close it.
C
clynchSep 1, 2025
Why AMF-BRUNS K90 ACTIVE raises the platform abruptly after extension?
- J
  Julie PatelSep 1, 2025
  If your AMF-BRUNS Back-in-Box-Lift raises the platform slightly but abruptly after it has extended, the 2/2-way valve is defective. Have the 2/2-way valve replaced in a specialist workshop.
D
David SmithAug 31, 2025
What to do if AMF-BRUNS K90 ACTIVE Lifting Systems platform is above retract position and won't lower?
- J
  Jasmine SchwartzAug 31, 2025
  If the platform is above the retract position and the AMF-BRUNS Back-in-Box-Lift doesn't lower when the "Retract Position" button is pressed, the end limit switch behind the transfer plate on the internal carriage might not be functioning. Try pulling the roller plunger out of the limit switch by hand and moving it in and out several times. If necessary, loosen the fastening nut slightly. You can also run to the retract position using the "Raise" and "Lower" buttons on the cable-connected remote control, the Bluetooth remote control or the Smartphone App.
L
Lisa JohnstonAug 30, 2025
What to do if AMF-BRUNS K90 ACTIVE Lifting Systems cannot be operated using the Smartphone App?
- A
  Adriana RoseAug 30, 2025
  If you can't operate the AMF-BRUNS Lifting Systems using the Smartphone App, ensure the app is connected to the lift's receiver or reinstall it. If the Bluetooth control box is not installed, contact customer service.
J
James HunterAug 28, 2025
Why is it impossible to operate AMF-BRUNS K90 ACTIVE Lifting Systems using the Bluetooth remote control?
- T
  Taylor SalazarAug 29, 2025
  If you can't operate your AMF-BRUNS Lifting Systems using the Bluetooth remote control, first ensure the remote is connected to the receiver by teaching it in again. If that doesn't work, charge the remote's battery. If problems persist, the remote itself may be defective and need checking or replacing. If the Bluetooth control box is not installed, contact customer service.