Firmware Pages and Descriptions
109
Modero VG Series Touch Panels - Instruction Manual
RGB Settings Page Elements (Cont.)
Status: Displays the input signal properties of the signal routed through the internal NXA-RGB card
(H-pixel x V-pixel @ Hz). An example is: 1024x768@85Hz.
Cable Variance: Allows you cycle through a choice of available cable compensation parameters (Short, Medium, and Long).
• This field adjusts the cable compensation for any signal degradation over a selected cable length.
• This adjustment is done by using preset calculations to take into account the length and type of cable being
used to transmit the signal.
• Toggling the field can correct some signal problems.
RGB Input Resolution: Use the UP/DN buttons to alter the input resolution of the RGB signal being routed through the internal NXA-
RGB card.
• Supported Input resolutions are:
- Auto: automatically detects the incoming signal. This is the recommended setting and should be used as
the default selection.
- 560 x 192, 560 x 384, 640 x 350, 640 x 416, 640 x 480, 720 x 532, 800 x 600, 900 x 720, 1024 x 768,
1280 x 768, 1280 x 800, 1152 x 864, 1280 x 1024, 1600 x 1200, HD 480p, HD, 720p, and HD 1080i.
• Note: These displayed resolutions correspond to the supported input resolution of the NXA-RGB card.
• Note: When using 1024 x 768, 1280 x 768, or 1280 x 800 it is recommended that you select those specific
resolutions using the input adjustment UP/DN buttons.
Phase: Use either the slider or the UP/DN buttons to alter the RGB tracking/signal level.
• Range = 0 - 31, default = 0.
Geometry: Provides an on-screen RGB Geometry popup dialog that allows you to select from several location and size
adjustment settings.
•Press the Adjust button to open the RGB Geometry popup dialog.
•Use the Hide button to close the popup.
• Range = 0 - 255, default = 0.
H Position Use the UP/DN buttons to alter the horizontal position level.
• Range = 0 - 255, default = 0.
H Size Use the UP/DN buttons to alter the horizontal size level.
• Range = 0 - 255, default = 0.
V Position Use the UP/DN buttons to alter the vertical position level.
• Range = 0 - 255, default = 0.
All Brightness: Provides an on-screen RGB Brightness popup dialog that allows you to select from several brightness level
adjustment settings.The bargraph only serves to give the user a visual indication of the individual brightness
levels and launch the RGB Brightness popup dialog.
Use the UP/DN buttons to alter the overall RGB brightness levels of the NXA-RGB card.
•Press the All Brightness bargraph to open the RGB Brightness popup dialog.
•Use the Hide button to close the popup.
• Range = 0 - 255.
Red Brightness Use the slider bar to alter the brightness of the red color value.
• Range = 0 - 255, default = 115.
• For more accurate control, you will have to go into the Full Screen Edit Mode described in the following
section.
Green Brightness Use the slider bar to alter the brightness of the green color value.
• Range = 0 - 255, default = 120.
• For more accurate control, you will have to go into the Full Screen Edit Mode described in the following
section.
Blue Brightness Use the slider bar to alter the brightness of the blue color value.
• Range = 0 - 255, default = 100.
• For more accurate control, you will have to go into the Full Screen Edit Mode described in the following
section.
All Contrast: Provides an on-screen RGB Contrast popup dialog that allows you to select from several contrast level
adjustment settings. The bargraph only serves to give the user a visual indication of the individual contrast levels
and launch the RGB Contrast popup dialog.
Use the UP/DN buttons to alter the overall RGB contrast levels of the NXA-RGB card.
•Press the All Brightness bargraph to open the RGB Brightness popup dialog.
•Use the Hide button to close the popup.
• Range = 0 - 255.
Red Contrast Use the slider bar to alter the contrast of the red color value.
• Range = 0 - 255, default = 60.
• For more accurate control, you will have to go into the Full Screen Edit Mode described in the following
section.
To Next Page
Loading...
