Programming
154
Modero VG Series Touch Panels - Instruction Manual
"^" Button Commands (Cont.)
^BOR Set a border to a specific border style associated with a border value for those buttons with a defined address range. Refer
to the Border Styles And Programming Numbers section on page 146 for more information.
Syntax:
"'^BOR-<vt addr range>,<border style name or border value>'"
Variable:
variable text address range = 1 - 4000.
border style name = Refer to the Border Styles And Programming Numbers section on page 146.
border value = 0 - 41.
Examples:
SEND_COMMAND Panel,"'^BOR-500.504&510.515,10'"
Sets the border by number (#10) to those buttons with the variable text range of 500-504 & 510-515.
SEND_COMMAND Panel,"'^BOR-500.504&510,AMX Elite -M'"
Sets the border by name (AMX Elite) to those buttons with the variable text range of 500-504 & 510-515.
The border style is available through the TPDesign4 border-style drop-down list. Refer to the Border Styles And
Programming Numbers section on page 146 for more information.
^BOS Set the video window slot ID # to the new Slot ID #. The new Slot ID # is set only if the specif ied slot is not the same as the
current slot selected. Pass-thru sets the pass-thru mode to On. This is an optional parameter and ONLY passes data to the
PC.
Syntax:
"'^BOS-<vt addr range>,<button states
range>,<slot number>,<pass-thru>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons 1 = Off state and 2 = On state).
slot number = 0 = No Video Fill
1 = Composite Video (Video Fill) (Video On) 1200V panels only have Slot 1 available.
2 = Component RGB
3 = Streaming Video.
pass-thru = Pass-thru disable = 0 or Pass-thru enable = 2.
Example:
SEND_COMMAND Panel,"'^BOS-500,1,1'"
Sets the button to display Composite video with no pass-thru.
Example:
SEND_COMMAND Panel,"'^BOS-500,1,2,1'"
Sets the button to display Component video with pass-thru enabled. Refer to theVideo Slide-Out Menu section on page 107
for more information on the slot assignments within a VG-Series panel.
^BPP Set or clear the protected page flip flag of a button. Zero clears the flag.
Syntax:
"'^BPP-<vt addr range>,<protected page flip flag value>'"
Variable:
variable text address range = 1 - 4000.
protected page flip flag value range = 0 - 4 (0 clears the flag).
Example:
SEND_COMMAND Panel,"'^BPP-500,1'"
Sets the button to protected page flip flag 1 (sets it to password 1).
^BRD Set the border of a button state/states. Only if the specified border is not the same as the current border. The border
names are available through the TPDesign4 border-name drop-down list.
Syntax:
"'^BRD-<vt addr range>,<button states range>,<border name>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons 1 = Off state and 2 = On state).
border name = Refer to the Border Styles And Programming Numbers section on page 146.
Example:
SEND_COMMAND Panel,"'^BRD-500.504&510.515,1&2,Quad Line'"
Sets the border by name (Quad Line) to those buttons with the variable text range of 500-504 & 510-515.
Refer to the Border Styles And Programming Numbers section on page 146.
To Next Page
Loading...
