Touch Panel Accessories
22
Modero VG Series Touch Panels - Instruction Manual
RGB RJ-45 connection and wiring information
This RJ-45 connector is used to route the signals connected to the RGB / Component input port on the rear of the AVB/RGB
Breakout Box to the VG-Series Modero panel. Standard CAT5 cable can be used for this connection with short cable runs under 50
feet (15.24 m). For cable runs over 50 feet (15.24 m), AMX recommends using the Belden Brilliance VideoTwist 7987. This Belden
cable is not CAT5 compliant, but is designed to control skew between the red, green, and blue video signals. Therefore, for longer
cable runs, the video quality will be much higher using the Belden VideoTwist 7987 cable versus standard CAT5 (or other Ethernet
compliant cables). The pinout of this RGB connector is given in the table below.
NOTE: The Belden cable only adjusts for RGB skew but may still need to be configured properly for cable length by using the Cable
Variance setting on the RGB Adjustment page (Video - RGB Settings Page section on page 108).
NOTE: It is important that the correct pairing is observed.
NXA-AVB/RGB Specif ications (Cont.)
Front Components: • 2-pin 3.5 mm mini-Phoenix connector for power to the touch panel
• Green LED provides an indication of both power and activity
- 1 blink/second indicates the unit is powered and active
- Multiple blinks/second indicates there is currently an activity in progress, such as a download. Do not
unplug the unit during this process.
• RJ-45 connector provides Ethernet signals to the touch panel
• RJ-45 connector provides differential audio/video signals between the touch panel and the box. This
connector routes Composite video, Stereo (left/right) audio, and microphone audio.
• RJ-45 connector provides RGB/Component video signals (being routed from the rear RGB/Component input
ports) and touch control information to the RJ-45 RGB connector on the NXA-RGB card (installed within the
panel). This connector routes VGA and Component video signals.
Rear Components: • 4-pin 3.5 mm mini-Phoenix connector for out-bound audio (from microphone)
• 6-pin 3.5 mm mini-Phoenix connector for in-bound (left/right channel) audio
• HD-15 D-Sub RGB/VGA/Component connector used to route an RGB (computer) or Component (DVD/HDTV)
signal to a target Modero panel (using the internal NXA-RGB card).
• Type-B USB device port input connector for pass-thru computer control (by connecting an external
keyboard or mouse device for use with different PC applications). The touch signals are routed to the touch
panel via the front RGB RJ-45 connector. Touch information is sent to and from the panel via this two-way
connector.
• 2-pin 3.5 mm mini-Phoenix connector for in-bound power (from a 12 VDC-compliant power supply)
• RJ-45 connector for Ethernet input from the control system
• BNC connector (female) for Composite or Chroma (COMP/Y). Composite NTSC, PAL and SECAM video is
provided via this connector.
• BNC connector (female) for luminance (C).
Included Accessories: • 4-pin 3.5 mm mini-Phoenix connector (41-5047)
• 6-pin 3.5 mm mini-Phoenix connector (41-5063)
• Rack Mount Kit (KA2250-40) with mounting bracket (62-2254-02)
• Two 2-pin 3.5 mm mini-Phoenix connectors (41-5025)
Other AMX Equipment: • AC-RK Equipment Rack Kit (FG575)
• NXA-MTC/RGB Combo Table Top cable (CA2250-70)
• NXA-RGBCBL, 15-pin to 5X BNC RGB Breakout cable (FG2250-80)
RGB RJ-45 Connector Pinouts and Signals
Pin Color Function Polarity
1 Orange-White Blue Video -
2Orange Blue Video +
3 Green-White Data (bidirectional) -
4 Blue Green Video -
5 Blue-White Green Video +
6 Green Data (bidirectional) +
7Brown-White Red Video -
8Brown Red Video +
To Next Page
Loading...
