Modero VG Series Touch Panels
16
Modero VG Series Touch Panels - Instruction Manual
NXD/T-1500VG Specif ications (Cont.)
Included
Accessories:
• Installation Kit for 15" NXD panels (KA2251-02):
- 2-pin mini-Phoenix connector (41-5025)
- Four Drywall clips (62-5924-05) and #6 -metal strips (80-0192)
- Three Phillips-head screws (#4-20 x 0.250 Black) (80-0114-08)
- Two CAT5 Suppression Ferrites (04-0014)
• Installation Kit for 15" and 17" NXT panels (KA2251-04):
- 2-pin mini-Phoenix connector (41-5025)
- One CAT5 Suppression Ferrites (04-0014)
- Three Phillips-head screws (#4-20 x 0.250 Black) (80-0114-08)
• Included within the RGB Kit:
- Modero VG Touch Panel (NXD/NXT-1200/1500/1700VG)
- NXA-AVB/RGB Breakout Box (FG2254-11)
- NXA-RGB internal RGB/VGA Interface Card (FG2260)
- NXA-RGBCBL, 15-pin to 5X BNC RGB Breakout cable (FG2250-80)
- NXA-MTC/RGB Modero 10’ foot Table Top Cable with RGB connector (CA2250-70)
• Included within the Video Kit:
- Modero VG Touch Panel (NXD/NXT-1200/1500/1700VG)
- Modero 10’ foot Table Top Cable (CA2250-50)
- NXA-AVB/ETHERNET Breakout Box (FG2254-10)
Other AMX
Equipment:
• CB-TP15 Conduit/Wallbox (FG032-10)
• CC-USB (Type A) to Mini-B 5-Wire programming cable (FG10-5965)
• Kensington Lock Bracket (FG2259-10) (optional only with NXTs)
• MAX-CSE MAX Video Encoder (FG2178-70)
• MB-TP15 Universal VESA Mounting Box (FG032-50)
• NXA-AVB/ETHERNET Breakout Box (FG2254-10)
• NXA-AVB/RGB Breakout Box (FG2254-11)
• NXA-BASE/B (FG2255)
• NXA-MTC/RGB Modero 10’ foot Table Top Cable with RGB connector (CA2250-70). This cable is not wall-
rated for NXD models.
• NXA-PCI80211G Wireless Card (FG2255-04)
• NXA-RGBKIT RGB upgrade kit for Composite Video touch panels (FG2255-11):
- NXA-AVB/RGB Breakout Box (FG2254-11)
- NXA-MTC/RGB Modero 10’ foot Table Top Cable with RGB connector (CA2250-70)
- NXA-RGB internal RGB/VGA Interface Card (FG2260)
- NXA-RGBCBL, 15-pin to 5X BNC RGB Breakout cable (FG2250-80)
- NXT Table Top replacement I/O plate with RGB connector opening (62-2250-59)
- NXD WallMount replacement adhesive overlay for existing I/O plate (53-2250-03)
Note: The NXT replacement I/O plate is a single piece which is meant to be swapped-out with the pre-
existing plate shipped with Composite Video panels. On NXD panels, the RGB connector opening is pre-
drilled into the I/O plate but can only be accessed by replacing the adhesive cover and maintaining the
existing overlay. When upgrading NXD panels with this kit, don’t replace the NXD I/O plate, only the
adhesive cover.
• NXA-RGBCBL, 15-pin to 5X BNC RGB Breakout cable (FG2250-80)
• NXA-RK15 Rackmount kit for 15" Wall Mount panels (FG2904-51)
• NXT-BP (FG2250-10)
•NXT-CHG (FG2250-50)
• PSN6.5 Power Supply (12 VDC) (FG423-41)
• Upgrade Compactflash (pre-programmed with f irmware):
NXA-CFTP4G, 4GB Compactflash Upgrade (FG2116-08)
To Next Page
Loading...
