AUMA AC 01.2 User Manual

DescriptionSignal
Torque fault in direction CLOSE
Torque fault CLOSE
Torque fault in direction OPEN
Torque fault OPEN
Torque fault in directions CLOSE or OPEN
Torque fault
Motor protection tripped
Thermal fault
One phase missing
Phase fault
High signal at fieldbus, digital output 1
Fieldbus DOUT 1
High signal at fieldbus, digital output 2
Fieldbus DOUT 2
High signal at fieldbus, digital output 3
Fieldbus DOUT 3
High signal at fieldbus, digital output 4
Fieldbus DOUT 4
High signal at fieldbus, digital output 5
Fieldbus DOUT 5
High signal at fieldbus, digital output 6
Fieldbus DOUT 6
High signal at fieldbus, digital output 7
Fieldbus DOUT 7
High signal at fieldbus, digital output 8
Fieldbus DOUT 8
High signal at fieldbus, digital output 9
Fieldbus DOUT 9
High signal at fieldbus, digital output 10
Fieldbus DOUT 10
High signal at fieldbus, digital output 11
Fieldbus DOUT 11
High signal at fieldbus, digital output 12
Fieldbus DOUT 12
No valid communication via fieldbus (despite available connection).
FailState fieldbus
Manual operation is active (handwheel is engaged); optional signal.
Handwheel active
Partial Valve Stroke Test (PVST) is active.
PVST active
Partial Valve Stroke Test (PVST) could not be successfully completed.
PVST fault
Partial Valve Stroke Test (PVST) was aborted or could not be started. Remedy: Perform RESET or restart
PVST.
PVST abort
This signal can be configured (parameter Failure (configurable) M0879) and comprises a combination
of the following signals which can also be configured:
●
Fault (Cfg) M0880
●
Warnings (Cfg) M0881
●
Not ready REMOTE (Cfg) M0882
Failure (configurable)
Function Interlock is active for operation mode REMOTE.
Interlock Remote
Function Interlock is active for operation mode Local.
Interlock Local
Interlock OPEN is active (enable signal for operation commands in direction OPEN available).
Interlock OPEN
Interlock CLOSED is active (enable signal for operation commands in direction CLOSE available).
Interlock CLOSE
The operation mode Interlock is active.
Interlock
<By-pass function> enable for operation commands of main or by-pass valves is active.
Bypass Sync Out
Operation command executed without enable signal Bypass Sync Out.Interlock by-pass
Safe ESD function (Emergency Shut Down) is active.
Safe ESD
Safe STOP function is active.
Safe Stop
A SIL fault has occurred (collective signal).
SIL fault
A SIL function is active. Collective signal of both states, Safe ESD or Safe STOP.
SIL function active
The actuator is switched on and no fault is present
System ok
Torque wrn OPEN
Torque wrn CLOSE
LPV (Lift Plug Valve) synchronisation signal. Master or slave actuator are in an end position.
LPV Sync Out
Operation command in direction OPEN from the master actuator to the slave actuator (SA).
LPV SA-OPEN
Operation command in direction CLOSE from the master actuator to the slave actuator (SA).
LPV SA-CLOSE
(PVST) Partial Valve Stroke Test should be executed
PVST required
The constant force spring is wound, the FQM is ready for fail safe operation.
FQM FS ready
The FQM (fail safe) fail safe function is requested (ESD requested).
FQM FS-ESD request
FQM has reached end position OPEN at the output drive side.
FQM end pos. OP
146
Actuator controls
Appendix AC 01.2/ACExC 01.2 Profinet

AUMA AC 01.2 Specifications

General

Brand	AUMA
Model	AC 01.2
Category	Control Unit
Language	English