Barco F80-Q12 - Maintenance

To Next Page

To Previous Page

161R5906852 /09 F80

13.1 Cleaning the lens........................................................................................................................ 162

13.2 Cleaning the exterior of the projector............................................................................................ 162

13.3 Filters ........................................................................................................................................ 162

About this chapter

This chapter contains general maintenance procedures.

Maintenance 13

Main Page

Table of Contents5
Safety9
General Considerations10
Important Safety Instructions11
Product Safety Labels14
Risk Group 3 Safety17
General Considerations17
High Brightness Precautions: Hazard Distance (HD)17
HD for Fully Enclosed Projection Systems19
HD in Function of the Lens Throw Ratio (TR)20
Getting Started23
Overview24
Projector Air Inlets and Outlets25
Local Keypad and LCD Panel25
Power Modes26
Power Mode Transitions26
Status Overview28
Power off Projector29
Increasing the Projector Life Time29
Operation in 24/7 Mode30
Using the RCU30
Projector Address31
Controlling the Projector31
Quick Setup Via Direct Access32
Remote Control Unit35
Basic Remote Control Unit36
Pulse RCU, Battery Installation37
Pulse RCU, Protocol Setup38
Pulse RCU, Functionality Overview39
Pulse RCU, Function of the "Button Pressed Indicator39
Pulse RCU, Function of the "RGB Filter" Button40
Using the Mini-Jack Connector of the RCU40
Pulse RCU, Function of the On/Off Button40
Using the RCU41
Pulse RCU, Silicone Protection Sleeve (Optional)42
Input & Communication45
Introduction46
Connection Panel46
Making Connections47
LED and Button Indication Chart47
GUI - Introduction49
Overview50
Navigation52
Test Patterns54
GUI - Source57
Displaying a Single Source58
Displaying Multiple Sources: Stitched Layouts58
Connector Settings60
GUI - Image63
Setting Image Levels Manually64
Adjusting the Sharpness65
Adjusting the Gamma Correction66
Setting the Desired Gamma Type67
Digital Shift & Zoom69
Realcolor P773
Setting the Output Resolution75
Brilliantcolor TM75
Displaying HDR Content76
GUI - Installation79
Configuring the Lens, Optical Zoom-Focus80
Configuring the Lens, Shift80
Configuring the Lens, Shift to Center81
Configuring the Lens, Tilt Sensor82
Manipulating the Rigging Frame83
Manipulating the Rigging Frame, Center Position84
Orientation85
Scaling Modes86
Warping87
Warping - On/Off88
Warping - Screen Size88
Warping - 4 Corners Adjustment91
Warping - Bow93
Warping - Warp Files97
Warping - Latency Control in a Multi Projector Setup99
Blending & Masking100
Basic Blend101
Blend & Blend Mask103
Blend Files105
Basic Black Level Adjustment106
RGB Gain Adjustment108
Black Level Files109
Illumination110
Projection111
Active Stereo & Passive Stereo111
Setup Process 3D Projection112
Connection Possibilities112
Setup113
GUI - Projector Profiles115
Saving the Current Projector Settings in a Profile116
Assigning a Created Projector Profile to a Preset118
Deleting a Projector Profile119
GUI - System Settings121
Remote Control122
Broadcast Address122
Projector Address122
IR Sensors123
Host Name - Custom Projector Name Setup124
LAN Communication125
Introduction to a Network Connection125
Wired IP Address Set up126
LAN over Hdbaset IP Address Set up128
DMX129
Trigger Outputs Control131
Changing the User Interface Language132
Themes133
Units (Measurement) System Setup133
Controlling the Backlight of the LCD Display134
Date and Time Setup - Automatically135
Power Settings - Standby Mode (ECO Mode)136
Operational Mode137
Lens Features138
Factory Reset139
Lens Calibration143
Rigging Frame Calibration144
Advanced Settings147
Remote Access - Enable Source Preview148
Service - Color Wheel149
Advanced Settings - Color149
Advanced Settings - Statistics150
Advanced Settings - Pixel Shift151
Checking the Status of the Laser Banks153
Advanced Settings - Tilt Sensor Calibration154
GUI - Status Menu157
Status Menu Overview158
Maintenance161
Cleaning the Lens162
Cleaning the Exterior of the Projector162
Filters162
A Specifications163
Specifications of the F80-Q7164
Specifications of the F80-Q9165
Specifications of the F80-Q12167
Specifications of the F80-4K7169
Specifications of the F80-4K9170
Specifications of the F80-4K12172
Dimensions of a F80174
B Connector Specifications177
Specifications DVI-I Inputs178
Specifications Displayport 1.2 Inputs178
Specifications HDMI 2.0178
Specifications SDI Inputs179
Specifications Hdbase T Input179
High-Bandwidth Digital Content Protection (HDCP)180
C Control Interface Specifications183
Lan/Ethernet184
USB-A Port184
DMX184
D Regulatory Information187
Product Compliance188
Disposal Information189
China Rohs Compliance189
Taiwan Rohs Compliance191
Turkey Rohs Compliance192
Production Address192
Contact Information192
Product Info (Taiwan)193
Download Product Manual193
E Overview Video Timings for Video Interfaces195
Overview Video Timings196
Overview Video Timings SDI Inputs197
Overview Video Timings HDMI 2.0 Inputs198
Overview Video Timings Displayport 1.2 Inputs200
Overview Video Timings Hdbaset Input201
Overview Video Timings DVI Inputs203
F DMX Chart205
DMX Chart, Basic206
DMX Chart, Extended206

Barco F80-Q12 - Maintenance

Table of Contents

Related product manuals