List of Tables
TABLE 1: MAIN DW1000 OPERATIONAL STATES / MODES ...... 16
TABLE 2: MODE 2 EXCERPT FROM DW1000 DATA SHEET
OPERATIONAL MODES TABLE .................................... 20
TABLE 3: GPIO DEFAULT FUNCTIONS .................................. 21
TABLE 4: REGISTER ACCESSES REQUIRED TO LOAD LDE MICROCODE
........................................................................... 24
TABLE 5: PREAMBLE DURATION FIELD VALUES IN EXTENDED
LENGTH DATA FRAME PHR ...................................... 28
TABLE 6: RECOMMENDED PAC SIZE .................................... 32
TABLE 7: REGISTERS IN THE RX DOUBLE-BUFFERED SWINGING-SET
........................................................................... 36
TABLE 8: AUTO-ACK PREAMBLE LENGTH DEPENDING ON RXPSR
AND RXPACC ........................................................ 51
TABLE 9: AUTO-ACK PREAMBLE LENGTH SELECTION IN EXTENDED
LENGTH FRAMES MODE ............................................ 51
TABLE 10: OTP MEMORY MAP ........................................... 59
TABLE 11: OTP_SRDAT REGISTER .................................... 60
TABLE 12: REGISTER ACCESSES REQUIRED TO PROGRAM THE OTP
........................................................................... 60
TABLE 13: AN EXAMPLE OF REGISTER ACCESSES REQUIRED TO
READ FROM OTP .................................................... 61
TABLE 14: AN EXAMPLE OF REGISTER ACCESSES TO PERFORM A
READ OF THE TEMPERATURE AND VOLTAGE SENSORS ...... 62
TABLE 15: REGISTER MAP OVERVIEW ................................... 63
TABLE 16: PREAMBLE LENGTH SELECTION ............................. 76
TABLE 17: PREAMBLE LENGTH REPORTING ............................ 94
TABLE 18: RXPACC ADJUSTMENTS BY SFD CODE................. 96
TABLE 19: REFERENCE VALUES FOR REGISTER FILE: 0X1E –
TRANSMIT POWER CONTROL, FOR SMART TRANSMIT
POWER CONTROL ................................................. 110
TABLE 20: REFERENCE VALUES REGISTER FILE: 0X1E – TRANSMIT
POWER CONTROL FOR MANUAL TRANSMIT POWER
CONTROL (SMART TRANSMIT POWER CONTROL DISABLED)
......................................................................... 110
TABLE 21: RECOMMENDED SFD SEQUENCE CONFIGURATIONS
FOR BEST PERFORMANCE ........................................ 118
TABLE 22: OTHER POSSIBLE SFD SEQUENCE CONFIGURATIONS
......................................................................... 119
TABLE 23: REGISTER FILE: 0X23 –AGC CONFIGURATION AND
CONTROL OVERVIEW .............................................. 120
TABLE 24: SUB-REGISTER 0X23:04 – AGC_TUNE1 VALUES 122
TABLE 25: SUB-REGISTER 0X23:0C – AGC_TUNE2 VALUES 122
TABLE 26: SUB-REGISTER 0X23:12 – AGC_TUNE3 VALUES 123
TABLE 27: SCALING FACTOR FOR CHANNEL NOISE ENERGY
ESTIMATION ......................................................... 124
TABLE 28: REGISTER FILE: 0X26 – GPIO CONTROL AND STATUS
OVERVIEW............................................................ 128
TABLE 29: REGISTER FILE: 0X27 – DIGITAL RECEIVER
CONFIGURATION OVERVIEW ..................................... 141
TABLE 30: SUB-REGISTER 0X27:02 – DRX_TUNE0B VALUES142
TABLE 31: SUB-REGISTER 0X27:04 – DRX_TUNE1AVALUES 144
TABLE 32: SUB-REGISTER 0X27:06 – DRX_TUNE1B VALUES144
TABLE 33: SUB-REGISTER 0X27:08 – DRX_TUNE2VALUES . 145
TABLE 34: REGISTER 0X27:26 DRX_TUNE4H VALUES ........ 147
TABLE 35: CONSTANTS FOR FREQUENCY OFFSET CALCULATION 148
TABLE 36: REGISTER FILE: 0X28 – ANALOG RF CONFIGURATION
BLOCK OVERVIEW .................................................. 149
TABLE 37: SUB-REGISTER 0X28:0B– RF_RXCTRLH VALUES 151
TABLE 38: SUB-REGISTER 0X28:0C– RF_TXCTRL VALUES ... 151
TABLE 39: REGISTER FILE: 0X2A – TRANSMITTER CALIBRATION
BLOCK OVERVIEW .................................................. 154
TABLE 40: SUB-REGISTER 0X2A:0B – TC_PGDELAY
RECOMMENDED VALUES ......................................... 158
TABLE 41: .................................................................... 159
TABLE 42: REGISTER FILE: 0X2B – FREQUENCY SYNTHESISER
CONTROL BLOCK OVERVIEW ..................................... 159
TABLE 43: SUB-REGISTER 0X2B:07 – FS_PLLCFG VALUES ... 160
TABLE 44: SUB-REGISTER 0X2B:0B – FS_PLLTUNE VALUES 161
TABLE 45: REGISTER FILE: 0X2C – ALWAYS-ON SYSTEM CONTROL
OVERVIEW............................................................ 162
TABLE 46: CONFIGURATIONS MAINTAINED IN THE AON MEMORY
ARRAY................................................................. 166
TABLE 47: REGISTER FILE: 0X2D – OTP MEMORY INTERFACE
OVERVIEW............................................................ 171
TABLE 48: RECEIVER OPERATING PARAMETER SETS ............... 176
TABLE 49: REGISTER FILE: 0X2E – LEADING EDGE DETECTION
INTERFACE OVERVIEW ............................................ 177
TABLE 50: SUB-REGISTER 0X2E:1806– LDE_CFG2 VALUES. 180
TABLE 51: SUB-REGISTER 0X2E:2804 – LDE_REPC
CONFIGURATIONS FOR (850 KBPS & 6.8 MBPS).......... 180
TABLE 52: REGISTER FILE: 0X2F – DIGITAL DIAGNOSTICS
INTERFACE OVERVIEW ............................................ 181
TABLE 53: REGISTER FILE: 0X36 – POWER MANAGEMENT AND
SYSTEM CONTROL OVERVIEW .................................. 190
TABLE 54: REGISTER ACCESSES REQUIRED FOR TRANSMITTER
CONFIGURATION PROCEDURE ................................... 201
TABLE 55: RECOMMENDED RX POWER LEVEL FOR ANTENNA
CALIBRATION ........................................................ 204
TABLE 56: RECOMMENDED TX-RX SEPARATION FOR ANTENNA
CALIBRATION ........................................................ 204
To Next Page
Loading...