GEM GPS3600 User Manual

○○○○○○○○○○○○○○○○○○○○○○
1•6 Introduction
○○○○○○○○○○○○○○○○○○○○○○
1•6 Introduction
RAM RESET
If you want to recall the factory settings, you can
reset the backed RAM memory.
1. Press EDIT to enter the “Edit” menu.
2. Press F2 to select the “Restore” command.
3. Press F3 to select the “Restore” command.
The following dialogue window is displayed.
3. Press ENTER to confirm the initialization, or ES-
CAPE to cancel the procedure.
If the procedure is confirmed, the instrument
can be played after few seconds.
BATTERY DISCHARGE MESSAGE
If the instrument has been left turned off for a
long period of time, the battery will slowly dis-
charge.
When the battery discharges completely, it caus-
es the total loss of all user programmed data.
If the battery has lost its charge completely, turn-
ing the instrument on will show the following
message:
The message cancels automatically after 2/3
seconds.
After the message cancels, be sure to save all of
your edited work to disk until after the battery has
sufficiently charged. Leave the instrument on for
a few hours to recharge the battery. One hour of
charge time corresponds to approximately one
day of use - the battery charge remains active
for approximately 15 days of non-use.
If you foresee leaving the instrument turned off
for a long period of time, be sure to save all user-
programmed data to disk to safeguard your data
against automatic erasure due to battery dis-
charge.
RAM RESET
If you want to recall the factory settings, you can
reset the backed RAM memory.
1. Press EDIT to enter the “Edit” menu.
2. Press F2 to select the “Restore” command.
3. Press F3 to select the “Restore” command.
The following dialogue window is displayed.
3. Press ENTER to confirm the initialization, or ES-
CAPE to cancel the procedure.
If the procedure is confirmed, the instrument
can be played after few seconds.
BATTERY DISCHARGE MESSAGE
If the instrument has been left turned off for a
long period of time, the battery will slowly dis-
charge.
When the battery discharges completely, it caus-
es the total loss of all user programmed data.
If the battery has lost its charge completely, turn-
ing the instrument on will show the following
message:
The message cancels automatically after 2/3
seconds.
After the message cancels, be sure to save all of
your edited work to disk until after the battery has
sufficiently charged. Leave the instrument on for
a few hours to recharge the battery. One hour of
charge time corresponds to approximately one
day of use - the battery charge remains active
for approximately 15 days of non-use.
If you foresee leaving the instrument turned off
for a long period of time, be sure to save all user-
programmed data to disk to safeguard your data
against automatic erasure due to battery dis-
charge.
○○○○○○○○○○○○○○○○○○○○○○
1•6 Introduction
○○○○○○○○○○○○○○○○○○○○○○
1•6 Introduction
RAM RESET
If you want to recall the factory settings, you can
reset the backed RAM memory.
1. Press EDIT to enter the “Edit” menu.
2. Press F2 to select the “Restore” command.
3. Press F3 to select the “Restore” command.
The following dialogue window is displayed.
3. Press ENTER to confirm the initialization, or ES-
CAPE to cancel the procedure.
If the procedure is confirmed, the instrument
can be played after few seconds.
BATTERY DISCHARGE MESSAGE
If the instrument has been left turned off for a
long period of time, the battery will slowly dis-
charge.
When the battery discharges completely, it caus-
es the total loss of all user programmed data.
If the battery has lost its charge completely, turn-
ing the instrument on will show the following
message:
The message cancels automatically after 2/3
seconds.
After the message cancels, be sure to save all of
your edited work to disk until after the battery has
sufficiently charged. Leave the instrument on for
a few hours to recharge the battery. One hour of
charge time corresponds to approximately one
day of use - the battery charge remains active
for approximately 15 days of non-use.
If you foresee leaving the instrument turned off
for a long period of time, be sure to save all user-
programmed data to disk to safeguard your data
against automatic erasure due to battery dis-
charge.
RAM RESET
If you want to recall the factory settings, you can
reset the backed RAM memory.
1. Press EDIT to enter the “Edit” menu.
2. Press F2 to select the “Restore” command.
3. Press F3 to select the “Restore” command.
The following dialogue window is displayed.
3. Press ENTER to confirm the initialization, or ES-
CAPE to cancel the procedure.
If the procedure is confirmed, the instrument
can be played after few seconds.
BATTERY DISCHARGE MESSAGE
If the instrument has been left turned off for a
long period of time, the battery will slowly dis-
charge.
When the battery discharges completely, it caus-
es the total loss of all user programmed data.
If the battery has lost its charge completely, turn-
ing the instrument on will show the following
message:
The message cancels automatically after 2/3
seconds.
After the message cancels, be sure to save all of
your edited work to disk until after the battery has
sufficiently charged. Leave the instrument on for
a few hours to recharge the battery. One hour of
charge time corresponds to approximately one
day of use - the battery charge remains active
for approximately 15 days of non-use.
If you foresee leaving the instrument turned off
for a long period of time, be sure to save all user-
programmed data to disk to safeguard your data
against automatic erasure due to battery dis-
charge.

GEM GPS3600 Specifications

General

Brand	GEM
Model	GPS3600
Category	Musical Instrument
Language	English