Honeywell Notifier NFS2-3030

To Next Page

To Previous Page

138 NFS2-3030 Programming Manual — P/N 52545:A 11/29/2005

Local Settings Chicago

I.2 Chicago

The LOCAL SETTING choice of CHICAGO disallows local drill or signal silence.

• The DRILL and SIGNAL SILENCE keys at the panel will not function.

• Annunciator Control Modules and SLC modules given a drill or signal silence Mode or

Type Code will not allow local drill or signal silence initiation.

Main Page

Table of Contents5
Section 1: General Information9
About this Manual9
UL 864 Compliance9
1: Products Subject to AHJ Approval9
2: Programming Features Subject to AHJ Approval9
Related Documents10
Introduction to the Control Panel11
1: Features11
Navigating Menu and Programming Screens12
Basic Procedure12
Getting Started13
1: Password Change13
Section 2: Main Menu17
Event Counts Display17
Multiple Event List17
History Display (History Select Screen)17
Read Status18
Program/Alter Status18
Printer Functions18
Section 3: Program19
General Information19
Panel Program20
1: Panel Program Menu (1)20
2: Network Parameters20
3: Panel Settings22
4: Panel Timers (Menu 1)24
5: Panel Timers (Menu 2)25
6: LCD Programming26
7: ACS Programming27
8: Supervision32
Panel Program Menu (2)33
1: Password Change33
2: Weekly Occupancy Schedule33
3: Remote Display Menu34
4: Loop Configuration36
5: Custom Action Message37
6: Event Logging38
7: Holiday Menu38
Point Program39
1: Detector Point40
2: Module Point46
3: General Zone49
4: Releasing Zone50
5: Logic Zone51
6: Trouble Zone54
7: Annunciator Board Label55
8: Audio Point Programming55
Delete Program56
Autoprogram Menu57
1: to Create a New Program57
2: to Add/Delete Devices from the Program57
3: Confirmation Screens58
Section 4: Alter Status63
Disable/Enable Point Selection63
Disable/Enable64
Detector Sensitivity65
1: Sensitivity Select65
Clear Verify Counters67
Clear History67
Walk Test68
1: Walk Test Menu70
2: Walk Test Loops Parameters71
3: Point Walk Test Activation71
4: Devices Test Selection72
Program Time/Date73
Control On/Off Point Select74
1: Control off74
2: Control on75
Section 5: Service Screens77
Version Information77
Power-Up Screen78
Bootloader Screen79
1: LCD-160 Download Menu79
2: Loop Download Menu80
Download Screen81
Application Corrupt Screen81
Appendix A: Menu Hierarchy83
A.1: Screens Overview83
Appendix B: Releasing Applications85
B.1: Releasing Zones85
B.2: NFPA Releasing Applications86
B.3: Abort Switches86
B.3.1: ULI Abort Switch88
B.3.2: IRI Abort Switch89
B.3.3: NYC Abort Switch90
B.3.4: AHJ Abort Switch92
B.3.5: Cross Zones93
B.3.6: Using Type Codes for Releasing Zones94
B.4: Miscellaneous105
B.4.1: Initiating Devices105
B.4.2: Warning Sounders106
B.4.3: Auxiliary Control Functions106
B.4.4: ACS Annunciation106
Appendix C: Special Zone Outputs107
C.1: Presignal and Positive Alarm Sequence (PAS)107
C.1.1: What Is Presignal and PAS107
C.1.2: Selecting Presignal and PAS Outputs107
Appendix D: Intelligent Sensing Applications109
D.1: Intelligent Sensing Overview109
D.2: Intelligent Sensing Features109
D.2.1: Drift Compensation and Smoothing109
D.2.2: Maintenance Warnings - Three Levels110
D.2.3: Self-Optimizing Pre-Alarm111
D.2.4: Detector Sensitivity111
D.2.5: Cooperative Multi-Detector Sensing112
D.3: Pre-Alarm112
D.3.1: Definition112
D.3.2: Alert Level112
D.3.3: Action Level113
D.4: Detector Sensitivity Settings113
D.4.1: How to Select Pre-Alarm and Alarm Sensitivity113
D.4.2: to Test Detectors Set below 0.50% Obscuration Per Foot114
D.5: Detector Status Display115
D.5.1: Detector Maintenance Display115
D.5.2: Print a Detector Maintenance Report115
D.5.3: to Interpret a Detector Status Display or Maintenance Report116
Appendix E: CBE: Zones and Equations119
E.1: Zones119
E.2: Equations120
E.2.1: Arguments120
E.2.2: Logic Equations120
E.2.3: Trouble Equations123
Appendix F: Detector Initialization125
F.1: Overview125
F.2: to Replace a Detector with a Different Type of Detector125
Appendix G: Type Codes127
G.1: What Are Type Codes127
G.2: How to Select a Type Code127
G.3: Type Codes for Input Devices127
G.3.1: Overview127
G.3.2: Type Codes for Intelligent Detectors127
G.3.3: Type Codes for Monitor Modules128
G.4: Type Codes for Output Devices129
G.5: Flashscan Codes130
Appendix H: System Troubles133
Appendix I: Local Settings137
I.1: Singapore137
I.2: Chicago138
Glossary139
Index141

Honeywell Notifier NFS2-3030

Table of Contents

Other manuals for Honeywell Notifier NFS2-3030

Related product manuals