To Next PageTo Next PageHow to override a tripped sensor on HySecurity Gate Opener?
To override a tripped sensor or fault condition on your HySecurity Gate Opener, press 'Open' or 'Close' momentarily. When you hear quick beeps, within 5 seconds, apply constant hold pressure to override the tripped sensor or fault.
General| Brand | HySecurity |
|---|---|
| Model | UL 325 |
| Category | Gate Opener |
| Language | English |
General safety precautions and best practices for gate operator use.
Specific safety guidelines for systems using monitored entrapment protection.
Lists gate operators requiring monitored entrapment sensors per UL 325.
Lists gate operators that maintain object detection features.
Details approved sensors compatible with HySecurity gate operators for UL 325.
Illustrates controller inputs and label changes for Smart DC models.
Illustrates controller inputs and label changes for Smart Touch models.
Details how sensor inputs are renamed and configured in the software.
Guidance on evaluating the gate site for entrapment zones and operator installation.
Instructions for wiring normally closed (NC) sensors to the controller.
Explains how to navigate the menu interface on the controllers.
Provides a table of installer menu settings for configuring sensor inputs.
Configuration for photo eye close logic and its effect on gate operation.
Configuration for photo eye open logic and its effect on gate operation.
Configuration for gate edge logic and its reaction to gate movement.
Setting for reversal logic based on sensor input.
Setting for photo eye output, enabling monitoring of NC sensors.
Setting for gate edge output, enabling monitoring of NC sensors.
Steps to temporarily power sensors and align photo eyes for proper function.
Procedure for overriding tripped sensors or fault conditions.
Troubleshooting alert for entrapment mode, with possible causes and fixes.
Troubleshooting alert for safe mode, indicating sensor trip or entrapment mode exit.
Troubleshooting alert for blocked photo eye close command.
Troubleshooting alert for blocked photo eye open command.
Troubleshooting alert for blocked gate edge activation.
Troubleshooting fault code indicating controller missed sensor sequence.
Troubleshooting error for dual gate communication issues.
Troubleshooting error for IES sensor disconnection.
Troubleshooting error for menu checksum issues.
Troubleshooting failure for program data errors.
Illustrates entrapment zones and sensor placement for slide gates.
Shows slide gate entrapment scenarios from the public side view.
Another view of slide gate site assessment for entrapment.
Illustrates entrapment zones and sensor placement for swing gates.
Details entrapment protection types for different gate operator categories per UL 325.
Explains specific provisions for Usage Class 4 gate operator installations.
Lists approved sensors for slide gate site assessment scenarios.
Lists approved sensors for swing gate site assessment scenarios.
Details UL 325 exception for barrier arms regarding entrapment protection.
Lists approved sensors for vertical lift site overview scenarios.
Shows sensor configuration for SlideSmart DC with multi-input device.
Sensor configuration for SwingSmart DC/DCS (Primary Operator).
Sensor configuration for SwingSmart DC/DCS (Secondary Operator).
Introduction to wiring diagrams for Smart Touch gate operators.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Introduction to wiring diagrams for Smart DC gate operators.
Details on using wire nuts or terminal blocks for SENSOR COM connections.
Explains how to navigate the menu interface on the controllers.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warning about NC sensor outputs and SENSOR COM terminal usage.
Warranty terms for products bought via authorized distributors and registered.
Limited warranty for products not purchased through authorized channels or not registered.
Warranty coverage for replacement parts.
Limitations and exclusions for all HySecurity product warranties.
Disclaimer of all other express or implied warranties.
Buyer's remedies for product nonconformities.
Exclusion of liability for consequential and incidental damages.
Clause regarding the severability of warranty provisions.
HySecurity's retention of intellectual property rights.
Governing law for the warranty terms.
Guidance on preparing for contact with HySecurity support or distributors.
