idp SOLID-510S - Rear Stacker Installation (Optional)

To Next Page

To Previous Page

2.6. Rear Stacker (Option)

SOLID-510 can install a rear stacker for option at the back of the printer. In case of SOLID-

510S and SOLID-510L, please install into the slots at the backside. In case of SOLID-510D,

please open the back cover of the printer and install it.

After that, set the value of ‘Card Out’ to ‘Back’ in the CardPrinterConfig Program.

In case of CP55 Dual, set the value of ‘Flipper Cover Open’ to ‘Ignore’ in the Configuration

Program

Figure 33 SOLID-510S installation of Rear Stacker

Figure 34 SOLID-510D installation of Rear Stacker

Figure 35 SOLID-510L installation of Rear Stacker

Main Page

Table of Contents3
Introduction10
Printer Outside Features10
Figure 1 SOLID-510 Front Features10
Figure 2 SOLID-510 Rear Features11
Figure 3 SOLID-510S (Standard)12
Figure 4 SOLID-510D (Dual)12
Figure 5 SOLID-510L (Laminator)12
Printer Inside Features13
Figure 6 SOLID-510 Inside Features13
Ribbon Cartridge Features15
Figure 7 Ribbon Cartridge Features15
Display and Buttons16
Figure 8 SOLID-510 Display and Buttons16
Printer Installation17
Connecting a Power and a USB Cable17
Figure 9 SOLID-510S Connection of Power and USB Cable17
Figure 10 SOLID-510D Connection of Power and USB Cable17
Figure 11 SOLID-510L Connection of Powers and USB Cable - 118
Figure 12 SOLID-510L Connection of Powers and USB Cable - 218
Fitting the Ribbon19
Figure 13 Top Cover Open19
Figure 14 Take out the Ribbon Cartridge19
Figure 15 Loading the Ribbon 120
Figure 16 Loading the Ribbon 220
Figure 17 Installing the Cleaning Roller20
Figure 18 Peeling the Protective Wrapper21
Figure 19 Installing the Ribbon Cartridge21
Figure 20 Close Top Cover21
Fitting a Laminating Film22
Figure 21 Take out the Film Cartridge22
Figure 22 Loading the Laminating Film22
Figure 23 Installing the Film Cartridge22
Loading the Cards23
Figure 24 Adjusting the Card Thickness Lever23
Figure 25 Preparing the Card 123
Figure 26 Preparing the Card 223
Figure 27 Loading the Cards 124
Figure 28 Loading the Cards 224
Figure 29 Loading the Cards 324
Figure 30 Loading the Cards 424
The Withdrawal of Printed Cards25
Figure 31 SOLID-510 Withdrawal a Card25
Figure 32 SOLID-510 Dividing a Stacker25
Rear Stacker (Option)26
Figure 33 SOLID-510S Installation of Rear Stacker26
Figure 34 SOLID-510D Installation of Rear Stacker26
Figure 35 SOLID-510L Installation of Rear Stacker26
Driver Installation (Windows 7 / 8 / 10)27
Figure 36 Install Win7 Driver 127
Figure 37 Install Win7 Driver 227
Figure 38 Install Win7 Driver 327
Figure 39 Install Win7 Driver 628
Figure 40 Install Win7 Driver 828
Figure 41 Install Win7 Driver 928
Figure 42 Install Win7 Driver 1028
Figure 43 Install Win7 Driver 1129
Figure 44 Install Win7 Driver 1229
Figure 45 Install Win7 Driver 1329
Figure 46 Install Win7 Driver 1430
Figure 47 Install Win7 Driver 1530
Driver Configuration31
Printer Properties31
Figure 48 Printer Properties31
Figure 49 Layout31
Figure 50 Input / Output32
Figure 51 Printing32
Figure 52 Laminating33
Figure 53 Encoding34
Figure 54 Magnetic Encoding Advanced Option34
Advanced Options35
Figure 55 Load/Save Option35
Other Settings38
Figure 56 Printer Sharing38
Figure 57 Ports38
Figure 58 Advanced39
Figure 59 Color Management39
Figure 60 Security40
Figure 61 Service40
Utilities41
Card Printer Config41
Figure 62 Cardprinterconfig Log-In41
Figure 63 Cardprinterconfig Start41
Figure 64 Cardprinterconfig - Card Printer Basic Setup42
Figure 65 Color Density44
Figure 66 Resin Black Density44
Figure 67 Overlay Density45
Figure 68 Cardprinterconfig - Card Printer Advanced Setup46
Figure 69 Cardprinterconfig - Flipper Setup49
Figure 70 Cardprinterconfig - Laminator Basic Setup50
Figure 71 Cardprinterconfig - Laminator Advanced Setup52
Network Configuration53
Figure 72 Rear View of SOLID-510 Printer 153
Figure 73 Rear View of SOLID-510 Printer 253
Figure 74 Running the Netadmin54
Figure 75 Network Printer Is Not Found54
Figure 76 Connecting to USB Port55
Figure 77 Netadmin Log-In55
Figure 78 USB Port State56
Figure 79 Rebooting the Network Module56
Figure 80 Reset to Default57
Figure 81 Upgrading the Firmware 157
Figure 82 Upgrading the Firmware 258
Figure 83 Upgrading the Firmware 358
Figure 84 Dynamic IP Configuration59
Figure 85 Static IP Configuration59
Figure 86 Network Service Configuration60
Figure 87 OCP Configuration60
Figure 88 Network User Configuration61
Card Printer Test62
Figure 89 Cardprintertest62
Figure 90 Magnetic Stripe Encoding65
Figure 91 Contact Smartcard Encoding67
Figure 92 Contactless Smartcard Encoding68
Firmware Update69
Figure 93 Run Cardprinterfirmware69
Figure 94 Select Firmware69
Figure 95 Update Firmware70
Optional Device Driver Installation71
Contact Smartcard Reader71
Figure 96 Contact Smartcard Reader Driver Installation71
Figure 97 License Agreement72
Figure 98 Installing the Contact Smartcard Reader Driver72
Figure 99 Completing the Smartcard Reader Driver Installation73
Contactless Smartcard Reader74
Figure 100 Found New Hardware Wizard74
Figure 101 Installation Method Selection75
Figure 102 Driver Location75
Figure 103 Completing the Driver Installation76
Troubleshooting77
Error Message77
Cleaning the Printer81
Figure 104 Exclusive Long Cleaning Card for SOLID-510 Printer81
Figure 105 Printer Cleaning Start81
Figure 106 Printer Cleaning Step 182
Figure 107 Printer Cleaning Step 282
Figure 108 Printer Cleaning Step 383
Figure 109 Printer Cleaning Step 483
Figure 110 Printer Cleaning Step 584
Figure 111 Printer Cleaning Step 684
TPH (Thermal Print Head) Replacement85
Figure 112 Thermal Print Head85
Figure 113 Print Head Setup85
Figure 114 Print Head Replacement86
Figure 115 Print Head Angle86
Laminator Head Replacement87
Figure 116 Disassemble the Laminator Head87
Figure 117 Assemble the New Laminator Head88
Card Movement89
Printing Quality90
Figure 118 Printing Quality Trouble 190
Figure 119 Printing Quality Trouble 290
Figure 120 Printing Quality Trouble 391
Figure 121 Printing Quality Trouble 491
Figure 122 Printing Quality Trouble 591
Magnetic Stripe Encoding92
General Operation92
Specification94

idp SOLID-510S - Rear Stacker Installation (Optional)

Table of Contents

Related product manuals