Inficon UL6000 Fab

To Next Page

To Previous Page

4 | Description INFICON

38 / 152 UL6000-Fab,-PLUS-Operating-instructions-iinc75en1-01-(2206)

I•RISE unit Pa/min

I•RISE permission User

Leak rate setpoint I•RISE 6E-2 Pa/min @ 10 L

Main Page

Table of Contents3
About this Manual8
Target Groups8
Warnings8
Definition of Terms8
Safety11
Intended Use11
Duties of the Operator13
Owner Requirements13
Dangers13
Scope of Delivery, Transport, Storage15
Description18
Function18
Operation Modes18
Operation Mode "Vacuum18
Operation Mode "Sniffing19
Design of Device20
Overall Device20
Control Unit23
START Button24
STOP Button24
ZERO Button25
Meaning of the Button Leds26
Meaning of the Status LED26
Design of Touchscreen27
Vacuum Connections29
Inlet29
Exhaust29
Purge Gas Connection30
Venting Connection30
Connections for Accessories and Control Signals31
Markings on the Device32
Technical Data32
Factory Settings34
Installation39
Setup39
Connect the Supplied Accessories43
Fastening Bracket for Sniffer Line SL3000 (Accessory, Optional)47
Connect Recipient/Test Object to Inlet Flange47
Connecting to the Power Supply System48
Checking the Operation of the Device49
Operation51
Switching on51
Basic Settings52
Set Language on the User Interface52
Setting Date, Time and Time Zone52
User Profile Settings52
Overview of Rights Groups52
Select, Modify, Create User Profile53
Modify Personal Settings54
Switch off Automatic Login54
Switch on Automatic Login54
Presentation of the Measurement Screen55
Changing the Presentation of the Line Graph55
Changing the Presentation of the Bar Graph56
Changing the Presentation of the Circle Graph57
Change General Display Settings57
Change Units58
Change Audio Settings58
Change the Protection Settings59
Set Maintenance Interval "Filter Sniffer Tip" or "Air Filter61
Activate or Deactivate Maintenance Requests61
Activating or Deactivating Calibration Requests62
Extending or Reducing Operation Options62
Measure Internal Calibration Leak after Run-Up63
Use Favorites63
Turn Notifications on or off64
Settings for the Measurements65
Select Operation Mode65
Select Gas65
Setting Setpoints65
Activate Vacuum Ranges66
Influence the Speed of the Backing Pump66
Switch TMP2 Mode on or off66
Hydro•S66
Set HYDRO•S67
Use HYDRO•S67
Setting the Machine Factor68
Set External Calibration Leak68
Change Pressure Limits68
Set and Use the Function ZERO69
Vent, Purge, Regenerate71
Change Leak Rate Filter72
Change Background Suppression73
Determine the Background of the Inlet Area74
Change SL3000 Settings for Sound / Light74
Change the Sniffer Line Pressure Monitoring74
Calibrating75
Internal Calibration75
External Calibration76
Check Calibration76
Measure Internal Calibration Leak76
Measure77
Leak Detection with I•RISE™ (Device-Dependent)78
Measuring Helium Ambient Concentration80
Measurement Data81
Switch on Data Recording and Configure Export81
Display Measurement Cycles82
Export Measurement Data Via Network83
Measurement Data Database: Information84
Information85
Call the Latest Information to the Current Measurement Value85
Call the Latest Information to the Current Calibration Value85
Information on Connected Accessories85
Retrieve Information about the Device85
Call Information on the Assemblies86
Call the Energy Data Information86
Call Information on the HYDRO•S86
Call Information on the SL3000 Sniffer Line87
Log87
Call the Error and Warning Log87
Call Calibration Log87
Call Result Log87
Call Maintenance Log87
Device Settings87
Viewing and Customizing Individual Parameters87
Saving and Managing Sets of Parameters88
Exporting or Importing Sets of Parameters89
Updating the Software89
Update the User Interface Software89
Updating the Software of the Basic Unit90
Update the Software in Expert Mode91
Activate Additional Function91
Use External Monitor91
Switch Back to the Internal Monitor92
View Vacuum Diagram92
Resetting to Factory Settings93
Logging off from the Device94
Switching off the Device94
Warning and Error Messages95
Warning and Error Messages UL3000/UL600096
Cleaning and Maintenance114
Cleaning the Housing114
Change the Filter Mat Inside the Tool Box114
Replacement of the Filter Mat on the Bottom of the Device115
Replacing the SL200 Sniffer Line Filter116
Replacing the SL3000 Sniffer Line Filter118
Mounting or Changing the Gas Cylinder119
Creating Screenshots120
Have the Device Serviced or Repaired120
Maintenance Plan122
Decommissioning124
Disposing of the Device124
Returning the Device for Maintenance, Repair or Disposal124
Accessories and Interfaces126
Accessories and Spare Parts126
I/O Module130
Create a Connection between the Device and the I/O Module130
Configuring Analog Outputs130
Configure Digital Inputs132
Configuring Digital Outputs133
Setting up the I/O Module Protocol135
Bus Module136
Creating a Connection between the Device and the Bus Module136
Setting a Bus Module Address136
Network137
Operate Leak Detector Via Web Browser (LAN)137
Configure the LAN Connection of the Leak Detector137
Setting the LAN Connection in the PC or Tablet138
Allow Client Access138
Operate Leak Detector Via Web Browser (Wireless LAN)139
Configure the Wireless LAN Connection of the Leak Detector139
Setting the Wireless LAN Connection in the PC or Tablet140
Allow Client Access141
Appendix142
Menu Path142
Diagnosis142
Settings142
Information144
CE Declaration of Conformity145
Rohs147
Index148

Inficon UL6000 Fab - Page 38

Table of Contents

Related product manuals