EasyManuals Logo

JCM DBV Series User Manual

JCM DBV Series
104 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #59 background imageLoading...
Page #59 background image
P/N 960-000180R_Rev. 1 {EDP #233427} © 2016, JAPAN CASH MACHINE CO., LTD.
6-5
Calibration and Testing DBV® Series DBV-400 Banknote Validator Section 6
Calibration
This section provides instructions for performing a
calibration of the DBV-400 Sensors.
When to Calibrate
Calibration should be performed when any of the
following conditions occur:
When removing one of the Circuit Boards;
When replacing one of the Circuit Boards;
When dirt adheres to the Sensors (See “Sensor and
Roller Cleaning Procedure” on page 2-11);
When the Banknote Acceptance Rate becomes
drastically degraded.
Placing the KS-095A Reference Paper
This section provides information regarding the
KS-095A Reference Papers settings and uses.
Perform the following steps to properly place the
KS-095A Calibration Reference Paper into the
DBV-400 Unit:
1. Press the Cash Box Release Button (Figure 6-23
a) in the direction indicated by the blue arrow.
Then pull slightly upward and out in the direction
indicated by the red arrow A, and remove the
Cash Box (Figure 6-23 b).
In the case of the optional Rear-Access Cash Box,
pressing the Cash Box Release Button (Figure 6-
24 a) can be skipped.
Pull the Rear-Access Cash Box upward (Figure 6-
24
) to unlock the Box Latch and then out in
the direction Figure 6-24
.
2. Press the Validation Guide Open/Close Latch
(Figure 6-25 a) upward, then pull the Validation
Guide (Figure 6-25 b) out of the DBV-400 Unit.
3. Remove Guide Chip A (Figure 6-26 a) and Guide
Chip B (Figure 6-26 b) from the DBV-400 Unit.
4. Insert the small end of the KS-095A Reference
Paper (Figure 6-27 a) through the backside of the
DBV-400 Banknote Path. The small end will
come out of the Bezel’s Banknote Insertion Slot
(Figure 6-27 b).
NOTE: Refer to Figure 6-1 and Figure 6-2
for the necessary Tool and Harness
Connections and USB Cable Type
Requirements respectively.
NOTE: Do not bend the Holders (Figure 6-22
a) or touch the Paper Surfaces on either side
of the KS-095A Reference Paper (
Figure 6-22
b
).
Figure 6-22 KS-095A Reference Paper
Figure 6-22 KS-095A Reference Paper
b
a
Figure 6-23 Placing KS-095A Reference Paper
Figure 6-23 Placing KS-095A Reference Paper 1
(Standard Cash Box)
The Standard Cash Box has a blue-colored Cash Box
Release Button
a
A
Figure 6-24 Placing KS-095A Reference
Paper 1 (Rear-Access Cash
Figure 6-24 Placing KS-095A Reference Paper 1
(Rear-Access Cash Box)
a
The Rear-Access Cash Box has a black-colored Cash
Box Release Button
Figure 6-25 Placing KS-095A Reference
Figure 6-25 Placing KS-095A Reference Paper 2
a
b
Figure 6-26 Placing KS-095A Reference
Figure 6-26 Placing KS-095A Reference Paper 3
a
b

Table of Contents

Other manuals for JCM DBV Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the JCM DBV Series and is the answer not in the manual?

JCM DBV Series Specifications

General IconGeneral
BrandJCM
ModelDBV Series
CategoryBank Note Validator
LanguageEnglish

Related product manuals