Leibinger Jet 2

To Next Page

To Previous Page

Group 7 Data Entry Page 97

Release 3.00 Leibinger-Jet 2 se

Figure 70

[E7]

[E50]

Enter password

[E7]

[E50]

Enter text „LEIBINGER“

[E7]

[E2]

Main Page

Table of Contents1
Table of Contents2
Group Directory7
Menu Level Index8
Publisher10
Introduction12
Document Information13
Safety14
Scope of Risks14
Safety Instructions and Recommendations14
Intended Use17
Sources of Danger17
Safety Sticker21
Operating Staff22
Dangers Due to Electric Energy22
Personal Protective Equipment22
Protective Devices22
Safety Measures at the Place of Installation23
Dangers through Consumables23
Accident Prevention25
Storage and Handling (Normal Use)25
First Aid Measures26
Fire Fighting Measures26
Measures in the Event of Accidental Release (Spillage)27
Technical Data28
Dimensions, Weights, Connections28
Ambient Conditions28
System Interfaces28
Power Parameters29
Font Forms29
Forms of Printing30
Font Combinations30
Manner of Working30
Software31
Transport/Start up32
Transport, Storage, Shipping32
Mounting32
Installation33
Mains Connection33
Data Interface X234
Transmission Protocol for Operating System LJOS34
Pin Assignment Plan35
Print Go Interface X536
Shaft Encoder36
Description and Pin Assignment36
Mechanic Installation37
Print Head38
Start up39
Initial Start up in an Empty Condition39
Initial Start up in a Full Condition41
Operation43
Construction/Structure43
Functional Principle44
Method of Working44
Drop Creation44
Drop Charging44
Drop Deflection45
Creation of a Character45
Summary of the Individual Procedures46
Operating Procedures and Operating Elements47
LCD Touch Display47
Switching On/Switching off Procedure47
Interval Operation49
Status Line in Normal Operation50
Status Line in Error Condition50
Software Reset51
Ink Switch52
Hardware Reset52
Potentiometer - Display Illumination53
Menu Structure54
Interfaces57
Data Interface57
Printgo Interface57
Shaft Encoder Interface57
Optional Outputs58
Optional Inputs58
Description of the Device59
Electronics Caabinet with LCD Touch Display59
Controller Board60
DC Power Supply62
Hydraulics Part63
Main Pump65
Suction Pump65
Viscosity Control66
Leak Detection67
Print Head67
Drop Production Unit with Oscillator69
Deflector Unit69
Nozzle Plate70
Nozzle Seal with Gutter70
Data Entry/Programming71
General71
Text Administration71
Text Entry72
Bold Print73
Font Parameters75
Text Editor78
Graphics Entry/Graphics Selection78
Graphics Editor79
Shift Code Input80
Barcode Input82
Barcode Information82
Barcode Selection84
Barcode Parameter85
Job Administration86
Opening Job86
Factory Setting & Default Jobs87
Deleting Jobs88
Storing and Listing Jobs89
User-/ Password Administration90
Password Levels (User Groups) and User Rights90
Call up Password Administration91
Activate User Administration (First Password Input)91
User Change and Password Change92
Login as Supervisor or Advanced Operator93
Change Passwords93
Logoff as Supervisor or Advanced Operator95
Password Forgotten96
Deactivate User-/Password Administration96
Print Start Parameters98
Print Delay and Print Repetition98
Printgo Distance99
Droplet Flight Time99
Print Go and Print Go Gate100
Meter Go Function101
Pre-Defined Print Stop103
Function Parameters104
Expiration Time and Shift Times104
Replacements and Text Sources105
Printing with the Function "Ex. Text105
Reset Counters107
Counter Settings108
Counter Programming109
Mode Normal and Reflected111
Service/Test/System Parameters112
Direct Start and Time/Date112
Monitoring Functions (Control Functions)113
Printgo- and Strokego Monitoring113
Encoder114
Encoder Parameters114
Job Change115
Printing with the Function "External Job Selection115
Service/Test- and Diagnosis Functions117
Summary Graph (Oscillator Voltage Curve)117
Motor Test118
Charging Voltage Test/Piezo Test119
Software Information120
Permanent Bleeding120
Hydraulic Test & Parameters121
Touch Screen Calibration123
Service Interval124
Trouble Shooting125
General125
Error Notification125
Error Messages126
Other Causes of Errors129
Equipping/Maintenance130
Equipping/Operation130
Refilling of Ink and Solvent130
Guarantee132
Service/Maintenance132
Daily Servicing Work132
Weekly Servicing Work132
Lubrication132
Nozzle Sealing133
Annual Servicing Work135
Filter Replacement and Ink Change136
Other Servicing Work139
Adjusting the Ink Jet in the Gutter139
Replacement of the Main Pump140
Replacement of the Battery and Fuse142
Servicing Work with more Difficult Operating Conditions143
Cleaning144
Daily Cleaning Work144
Cleaning the Print Head144
Cleaning the Deflector Unit and Gutter145
Weekly Cleaning Work146
Cleaning of the Spindle and Guides of the Nozzle Seal146
Other Cleaning Work147
Cleaning the Nozzle147
Cleaning the Suction Pump149
Further Maintenance Measures (Service Intervals)151
Taking out of Operation152
Dismantling/Disposal152
Replacement Parts153
Replacement Parts Electronics153
Replacement Parts Hydraulics153
Replacement Parts Print Head SK2154
Special Tools154
Cleaning/Servicing Accessories155
Periphery155
Data Entry Devices156
Consumables157
Appendix158
Hydraulics Diagram158
Interface Layout Plan159
Calculation of the Print Speed161
Fonts164
List of Graphics166
Technical Drawings167
List of Keywords/Index169
List of Illustrations175

Leibinger Jet 2 - Page 97

Table of Contents

Related product manuals