Lenze i700

Lenze · i700 servo inverter · reference manual · DMS 3.0 EN · 06/2016 · TD06 325
11 Appendix
11.1 Table of attributes
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
0x3412 Sensorless synchronous control: Low speed range, controlled
1: Additive accelerating current UNSIGNED_16 - P
2: Standstill holding current UNSIGNED_16 - P
0x3413
Sensorless synchronous control: Low speed
range, operating mode
UNSIGNED_8 - P
Axis B - feedback system
0x3440
Encoder: Type UNSIGNED_8 - P CINH
0x3441
Hiperface: Parameter
1: Hiperface: Determined type code UNSIGNED_8 -
2: Hiperface: User def. encoder - type code UNSIGNED_8 - P CINH
3: Hiperface: User def. encoder - specifiable
revolutions
UNSIGNED_16 - P CINH
4: Hiperface absolute value fault: Response UNSIGNED_8 - P
5: Hiperface: Serial number STRING(50) -
6: Hiperface: Raw data - Actual position UNSIGNED_32 - Tx
7: Hiperface: Detected Increments / revolution UNSIGNED_16 - Tx
8: Hiperface: Type code supported by firmware UNSIGNED_8 - Tx
9: Hiperface: Encoder type UNSIGNED_8 - Tx
10: Hiperface: Period length of linear encoders UNSIGNED_32 - Tx
0x3442 Encoder: Parameter
1: Encoder: Increments / revolution UNSIGNED_32 - P CINH
2: Encoder: Supply voltage UNSIGNED_8 1/10 P CINH
3: Encoder: Angle drift - Actual angle error INTEGER_16 1/10 OSC Tx
4: Encoder: Signal quality - Actual amplitude UNSIGNED_8 - OSC
0x3443 Resolver: Number of pole pairs UNSIGNED_8 - P CINH
0x3444
Resolver error compensation: Parameter
1: Resolver error compensation: Angle INTEGER_16 - P
2: Resolver error compensation: Cosine track
gain
UNSIGNED_16 - P
3: Resolver error compensation: Sine track gain UNSIGNED_16 - P
0x3445
Feedback system: Response to open circuit UNSIGNED_8 - P
0x3446
Feedback system: Specifiable number of
revolutions
UNSIGNED_16 -
0x3447 Feedback system: Open circuit detection
sensitivity
UNSIGNED_8 - P
0x345F
Feedback system: Parameter CRC UNSIGNED_32 -
Axis B - pole position identification
0x3460
Monitoring pole position identification:
Response
UNSIGNED_8 - P
0x3461
Pole position identification PPI (360°)
1: PPI (360°): Current amplitude UNSIGNED_16 - P CINH
2: PPI (360°): Ramp time UNSIGNED_16 - P CINH
3: PPI (360°): Direction of rotation UNSIGNED_8 - P CINH
4: PPI (360°): Fault tolerance UNSIGNED_8 - P
5: PPI (360°): Absolute current amplitude UNSIGNED_32 1/100
0x3462 Pole position identification PPI (min. movement)
1: PPI (min. movement): Current amplitude UNSIGNED_16 - P CINH
2: PPI (min. movement): Ramp time - current UNSIGNED_16 - P CINH
3: PPI (min. movement): Gain UNSIGNED_16 - P
4: PPI (min. movement): Reset time UNSIGNED_16 1/10 P
5: PPI (min. movement): Max. move permitted UNSIGNED_8 - P
6: PPI (min. movement): Absolute current
amplitude
UNSIGNED_32 1/100
Index Name Data type Factor Attributes
Greyed out = read only