prw2101a0600p_01
4 / 105
5.4.13.
Prog CS........................................................................................................... 64
5.5. PROGRAMMING DEVICES.......................................................................... 65
5.6. REMOTE PROGRAMMING .......................................................................... 66
5.6.1. Editing the linearisation table .......................................................................... 68
5.7. RELAY CONFIGURATION........................................................................... 69
5.7.1. Relay Selection ............................................................................................... 69
5.7.2. Properties of the selected relay....................................................................... 70
5.7.3. Relay programming......................................................................................... 71
5.7.3.1 Source selection ................................................................................. 71
5.7.3.2 Function.............................................................................................. 72
5.7.3.3 Configuring parameters ...................................................................... 80
5.7.3.4 Invert................................................................................................... 81
5.7.3.5 Deleting TOT ...................................................................................... 81
5.7.3.6 Refreshing TOT .................................................................................. 82
5.7.3.7 Testing................................................................................................ 82
5.8. OPERATION AND PARAMETERS OF CURRENT OUTPUTS .............................. 84
5.8.1. Selection of Current outputs............................................................................ 84
5.8.2. Properties of the selected Current Output....................................................... 85
5.8.3. Current Output programming .......................................................................... 85
5.8.3.1 Source selection ................................................................................. 85
5.8.3.2 Function.............................................................................................. 86
5.8.3.3 Parameter configuration ..................................................................... 87
5.8.3.4 Testing................................................................................................ 87
5.9. THE BOOT PROCESS ............................................................................... 88
5.10. MEASUREMENT MODES ........................................................................... 90
5.11. SAVING, LOADING THE CONFIGURATION OF THE MULTICONT ..................... 91
6. ERROR CODES............................................................................................. 92
7. HARDWARE PROTECTION OF THE SETTINGS ........................................ 94
8. FUSE REPLACEMENT ................................................................................. 95
9. SERVICING.................................................................................................... 96
9.1. BOX MESSAGES:..................................................................................... 96
9.2. OTHER MESSAGES:................................................................................. 97
9.3. TROUBLESHOOTING................................................................................. 98
9.3.1. It is impossible to enter the „Main menu”/”Relays” or „Main menu”/„Current
outputs” menu: ................................................................................................ 98
9.3.2. It is impossible to enter the „Main menu”/”Devices” menu: ............................. 98
9.3.3. A „Please wait” message appears upon selecting „DEV detect”.................... 98
9.3.4. The result of „DEV detect” is the „No device” message .................................. 98
9.3.5. The unit does not start up when switched on ..................................................98
9.3.6. The „Response” error entry is too frequent......................................................98
9.4. ADDITIONAL INFORMATION ........................................................................99
9.4.1. Problems that may occur during remote programming:...................................99
9.4.2. MultiCONT transmits the parameters without examining them, and the testing is
done by the device...........................................................................................99
9.4.3. Use of Second HART Master ( Hand-Held or HART modem + Eview
configuration software) ....................................................................................99
9.4.4. Upon exiting remote programming, the unit tests to see if the transmitter really
exited the remote programming mode.............................................................99
9.4.5. When a transmitter does not respond, then „Response” error is entered into the
table, but upon termination of the error (the device responds), this entry is
automatically cleared from the table (and does not need to be acknowledged)99
9.4.6. Upon exiting the menu, MultiCONT immediately saves the modifications.......99
9.4.7. The error list is cleared when the device is put off...........................................99
Appendix 1. ManufacturerID codes of HART-capable devices 100
Appendix 2. The menu system of the MultiCONT P-200 101-102
Appendix 3. Relay programming 103
Appendix 4. Current output programming 104
Appendix 5. Measurement mode 105
To Next Page
Loading...