Omron CX-INTEGRATOR - V1.1 User Manual

1-4 PLC Connecting Cables
1-4-1 Direct Serial Connections to a PLC
Note Connecting the PLC Using a USB Port on the Computer
A USB port on the computer can be used to connect the computer running the
CX-Integrator to a PLC. To do so, connect the computer to the PLC as shown below
using a CS1W-CIF31 USB-Serial Conversion Cable. When connecting the computer to
a CP-series PLC, it is possible to make a direct connection using a
commercially-available USB cable (B type – A type connectors).
The driver software included with the CJ1W-CIF31 must be installed on the computer
to use a USB port to connect the CX-Integrator. Refer to the PDF User’s Manual
included with the CS1W-CIF31 USB-Serial Conversion Cable for details.
PLC Connection Methods
Computer
running
CX-Integrator
CS1W-CIF31 Cable 1
Cable 2
(when required)
PLC
CS1W-CIF31
USB Connecting Cable
+
or
or
CS1W-N226/626 CS/CJ-series
Peripheral Port Programming
Device Connecting Cable
XW2Z-
@@@
RS-232C Programming
Device Connecting Cable
CQM1H-CIF02 C-series
Peripheral Port Programming
Device Connecting Cable
+
CS1W-CN118
RS-232C-CS/CJ-series
Peripheral Conversion Cable
CS1W-CN114
C-series-CS/CJ-series
Peripheral Conversion Cable
CS/CJ-series CPU Unit Connection Patterns
USB
Connecting
Cable
Cable 1 Cable 2 Port Serial
communications
mode
Model Connector Model Connector Connector Model Connector (network
type)
D-sub 9-pin
female
CS1W-CN226/626
(length: 2 m/6 m)
CS/CJ
peripheral
Not needed. CS/CJ
peripheral
Peripheral
(Toolbus)
or Host Link
(SYSWAY)
D-sub 9-pin
female
CQM1-CIF02
(length: 3.3 m)
C peripheral C peripheral CS1W-CN114
(length: 5 cm)
CS/CJ
peripheral
Host Link
(SYSWAY)
D-sub 9-pin
female
XW2Z-200S-CV
/500S-CV
(length: 2 m/5 m)
D-sub 9-pin
male
D-sub 9-pin
female
CS1W-CN118
(length: 0.1 m)
CS/CJ
peripheral
Peripheral
(Toolbus)
or Host Link
(SYSWAY)
D-sub 9-pin
female
XW2Z-200S-V
/500S-V
(length: 2 m/5 m)
D-sub 9-pin
male
D-sub 9-pin
female
CS1W-CN118
(length: 0.1 m)
CS/CJ
peripheral
Host Link
(SYSWAY)
D-sub 9-pin
female
XW2Z-200S-CV
/500S-CV
(length: 2 m/5 m)
RS-232C
D-sub 9-pin
male
Not needed. RS-232C
D-sub 9-pin
female
Peripheral
(Toolbus)
or Host Link
(SYSWAY)
CS1W-CIF31
D-sub 9-pin
female
XW2Z-200S-V
/500S-V
(length: 2 m/5 m)
RS-232C
D-sub 9-pin
male
Not needed. Host Link
(SYSWAY)
1-17

Omron CX-INTEGRATOR - V1.1 Specifications

General

Brand	Omron
Model	CX-INTEGRATOR - V1.1
Category	Software
Language	English