Panasonic AWRP120

41
Returning the unit to the factory default state (INITIALIZE)
You can restore the settings stored on the unit to the factory defaults
(INITIALIZE)
When executing INITIALIZE, select one of “ALL” or “SETUP”
ALL : Restores all settings to the factory default state (executes
INITIALIZE)
SETUP: Restores only some settings to the factory default state
(executes INITIALIZE)
 For details on initializing the settings stored on a remote camera,
refer to the Operating Instructions for the remote camera
Note
Also, when you execute INITIALIZE, the data stored on the unit and the
following statuses are restored to the factory default state
<Initialized data and statuses (ALL or SETUP)>
 Tracing memory data
 Movement speed when recalling preset memory
(PRESET SPEED)
 Remote camera selection status
 Camera group selection status
 ENABLE button lighting statuses
<Initialized data (ALL)>
 User authentication settings (user name and password)
<Initialized setting items>
√: Target ―: Not target
Button
number
Menu name Setting item
INITIALIZE
ALL SETUP
[24] CAMERA SETUP 1 CAM POWER √ √
2 AUTO ON √ √
3 RECALL PST SPD √ √
4 TALLY OUT √ √
[25] RP SETUP 1 FOCUS/IRIS √ √
2 P/T CURV √ √
3 LCD BACKLIGHT √ √
4 ENABLE BUTTON √ √
5 MENU CONTROL √ √
6 GLOBAL AREA √ √
7 IP ADDRESS √ ―
8 SUBNETMASK √ ―
9 GATEWAY √ ―
11 PORT CAM1 to 20 PORT CAM10 √ ―
[26] PAN DIRECTION 1 CAM1
to 100 CAM100 √ √
[27] TILT DIRECTION 1 CAM1
to 100 CAM100 √ √
[28] ZOOM DIRECTION 1 CAM1
to 100 CAM100 √ √
[29] FOCUS DIRECTION 1 CAM1
to 100 CAM100 √ √
[31] PM GRP1 1 PM GRP1 MODE √ √
2 PM GRP1 1/10 to 11 PM GRP1 10/10 √ √
12 PM GRP1 ALL √ √
[32] PM GRP2 1 PM GRP2 MODE √ √
2 PM GRP2 1/10 to 11 PM GRP2 10/10 √ √
12 PM GRP2 ALL √ √
[33] PM GRP3 1 PM GRP3 MODE √ √
2 PM GRP3 1/10 to 11 PM GRP3 10/10 √ √
12 PM GRP3 ALL √ √
[34] PM GRP4 1 PM GRP4 MODE √ √
2 PM GRP4 1/10 to 11 PM GRP4 10/10 √ √
12 PM GRP4 ALL √ √
[35] USER BUTTON 1 USER1
to 8 USER8 √ √
[36] CTRL TYPE 1 CAM1
to 100 CAM100 √ ―
[38] SWAP IP 1 CAM1
to 100 CAM100 √ ―
[39] MANUAL IP 1 CAM1
to 100 CAM100 √ ―
[40] PORT NO 1 CAM1
to 100 CAM100 √ ―
[41] SW SETUP 1 SW CTL √ ―
2 SW IP ADDRESS √ ―
[42] SW FUNCTION 1 SWLINK
to 16 CAMINF_ALARM √ √
[43] SW INPUT 1 INPUT1
to 100 INPUT100 √ ―
[44] TALLY 1 TALLY IN1
to 10 TALLY IN10 √ √
[45] GPI OUT 1 CAM OUT1
to 10 CAM OUT10 √ √
 For the factory default settings, refer to “Table of setting items (menus)” (pages 53 to 55)