Proyecson PAA20+ - Page 49

148 pages

Save Page as PDF

To Next Page

To Previous Page

Figure 8.3.1C

12. Now the Paa20+ is configured and ready for the associated

automation and trigger cues, to be created.

INSTALLATION MANUAL: PAA20+ V 2.0 (10/2021) 49

Main Page

Table of Contents3
Safety6
General6
Installation6
Proper Use7
Introduction8
Features9
Frontal Panel11
Rear Panel12
Connection Procedure13
Connection to Dolby Dss Servers13
Connection to Doremi Dcp Servers over Ethernet14
Connection to Doremi Dcp Servers Using Serial Port15
Connection to Gdc Servers over Ethernet16
Connection to Gdc Servers Using the Serial Port17
Connection to Qube Xp-D Server Using the Serial Port18
Connection to Datasat Dc20 Server Using Serial Port19
Connection to Barco Alchemy (Icmp) over Ethernet20
Connection to Ims Servers over Ethernet21
Connection to Christie Imb S2 Server over Ethernet22
Administration of the Paa2023
Connecting with the Paa2023
Paa20+ Web Admin Interface24
Servers Configuration43
Dolby Dss Servers Configuration43
Doremi Dcp and Show Vault Series Servers Set-Up47
Adding the PAA20+ to Doremi DCP and SV Servers: Ethernet Interface47
Adding the PAA20+ to Doremi DCP and SV Servers: Serial Interface50
Setting up the Output Cues for Doremi DCP and SV Servers (Non-Xml Library Method)52
Setup Output Cues for Doremi DCP and SV Servers Using Xml Library56
Setup the Input Cues Using PAA20+ Xml Library61
Doremi, Dolby and Nec Ims Series Servers Set-Up65
Adding the PAA20+ to Doremi, NEC and Dolby IMS Servers65
Setting up Output Cues for Doremi, Dolby and NEC IMS Servers with Xml Lib70
Setting up Input Cues for Doremi, Dolby and NEC IMS Servers with Xml Lib74
Barco Alchemy Icmp Server Set-Up77
Adding the PAA20+ to Barco Alchemy ICMP Servers: Ethernet Interface77
Setting up the Output Cues for Barco Alchemy ICMP Servers Using Xml Library84
Setting up the Paa20+Inputs for Barco Alchemy ICMP Servers87
Gdc Server Set-Up91
Adding the PAA20+ to the GDC Server: Ethernet Interface91
Qube Server Set-Up99
Adding the PAA20+ to the Qube Server: Serial Interface99
Configure the Qube Inputs on the PAA20102
Datasat Server Set-Up104
Christie Imb S2 Server Set-Up105
Configure the Christie IMB S2 Automation for the PAA20105
Outputs / Inputs of the Paa20109
Output 1 Connector109
Output 2 Connector110
Output 3 Connector111
Input Connector112
Examples of Input Connection113
Input with a Negative Common113
Input with a Positive Common114
Serial Prot Pin-Out115
Firmware Versions116
Electrical Requirements118
Technical Draws, Labels, Dimensions and Weight119
Appendix A: Serial Commands for Dolby120
Appendix B: Commands for Doremi and Ims Servers122
Appendix C: Table for Tcp/Ip Changes Annotation124
Appendix D: Paa20+ Tester and Programmer Software125
Ap D.1 Hardware Requirements125
Ap D.2 Installation125
Ap D.3 Use126
Ap D.3.3.1 Abstract129
Ap D.3.3.2 Requirements129
Appendix E: Commands for Gdc Servers130
Appendix F: Commands for Qube Servers132
Appendix G: Qube Automation Files Examples134
Appendix H: Commands for Barco Alchemy (Icmp) and Christie146
Appendix I: Commands for Barco Alchemy (Icmp) Remote148
Player Management148

Proyecson PAA20+ - Page 49

Table of Contents