PRÜFTECHNIK ROTALIGN ALI 3.500 - Page 160

6-39
ROTALIGN 01.2000
E
EDIT (configuration) ................................3-2
EDIT (dimensions) ....... 4-21,4-40,5-6,5-14
EDIT FILE INFO ....................................3-6
EDIT NAME ..............................................3-4
Electronic memory ..............................2-12
Emitter - see laser
"Enter" key ................................................2-4
Entering dimensions ................ 4-4,4-21,5-14
Error messages .......................................6-13
F
FILE INFO (file) ........................................3-6
FILE TYPE (H,V, H&V) ..........................3-5
Fit shims ...................................................5-9
Flange diameter (vert mach.)...................5-6
Flange-mounted horizontal machines ....5-13
Foot positions/errors ....................... 4-5,4-50
G
Gap/offset (coupling)
during setups ......................................4-20
in results ............................ 4-50,4-59,4-64
theory........................................... 6-3 - 6-4
GRAPH REPORT (report) .........................3-7
Growth (thermal) ...................................4-61
H
H ? V (Horiz./Vert.) ................................4-58
H ZOOM - see ZOOM
Hardcopy (screen printout) ......................3-7
HISTRY ...................................................4-58
Horizontal machine
flow chart ..............................................4-8
standard alignments................... 4-1 - 4-66
Quick Check ................................. 4-3 - 4-5
Horizontal alignment, move ...............4-51
Humidity ...............................................1-8
I
Inch fractions..........................................4-22
Incident light ........................................1-9
Indicator LEDs ......................................2-6
Infrared link ...........................................6-23
INIT TABLE (tolerances).........................4-64
Installing components ...........................1-9
Intended use .........................................1-5
Interfaces ................................. 1-9,2-7,2-8
Intrinsic Safety ............................... 1-6,2-9
L
L ? R (left/right machine) ............. 4-17,4-59
LAMIBLOC ............................................6-3
LANGUAGE ...........................................3-2
Laser .......................................................2-13
adjustment ............................... 4-23 - 4-25
mounting .........................................4-12
optics.....................................................6-4
safety .................................................1-7
"LASER END","LASER OFF" ...................6-13
LEDs
computer ...............................................2-6
laser ....................................................2-13
receiver ...............................................2-15
LENGTH R1..R2 (dial gauges)................4-39
LPT/COM .................................................3-8
LPT port - see printer
M
"M" key - see Measure key
Machine dimensions ...............................4-16
Machine preparation ....................... 4-10,6-7
Machine setup ........................................4-17
Machine trains ........................................4-15
Magnetic sliding bracket ........................6-18
"MAIN", Main battery ...............................2-9
Mains adapter.........................................6-17
MAX COUPLING VALUES .............. 4-62,4-64
MEAS. MODE .........................................4-28
MEASURE AT 0,3,6,9 .............................4-35
Measurement..........................................4-28
DIAL GAUGE VALUES .........................4-39
distance .................................................1-9
Mode ...................................................4-33
MULTIPOINT .......................................4-36
Options................................................4-43
PASS MODE ........................................4-36
principle ..........................................6-10
range .....................................................1-9
warnings ..........................................4-33
Measurements, deactivating ...................4-41
Memory ................................... 2-12,3-6,6-11
Menu ....................................... 3-2,4-6,4-7
Minus key (–) .................................. 2-4,4-22
MOVE .....................................................4-51
horizontal machines ................. 4-53 - 4-54
vertical machines ..................................5-9
Moveable machine - see Stationary
Multiplication key...................................4-22
MULTIPOINT ..........................................4-36
Index