Raven Envizio Pro - Chapter 4 CAN Networking and Diagnostics

232 pages

To Next Page

To Previous Page

Manual No. 016-0171-148 29

CAN Networking and Diagnostics

FIGURE 2. Envizio Pro Dual Product (Liquid/Granular) CAN Control System

Main Page

Default Chapter3
- Table of Contents3
- Calibration Reference Sheet9
- Unit Definitions and Conversions10
  - Unit of Measure Definitions10
  - Unit of Measure Conversions10
Important Safety Information11
- Safety Information11
  - Hydraulic Safety12
  - Electrical Safety12
Chapter 2 Introduction13
- Introduction13
- Envizio Pro and Envizio Pro II Features14
- Front Panel16
  - Resistive Touch Screen Technology17
  - Icon Based Operation17
- Rear Panel18
- Care and Use19
  - Technical Specifications19
Chapter 3 Installation21
- Kit Contents22
- Mounting the Field Computer26
- Cable Platforms and Connections27
  - Generation 1 Cable Connections27
  - Generation 2 Cable Connections29
- DGPS Antenna30
- Installing Optional Equipment32
- Canbus Network Connection35
- Installation21
  - Overview of the Installation Process21
CAN Networking and Diagnostics37
Chapter 4 CAN Networking and Diagnostics39
- CAN Diagnostics40
- Programming Canbus Nodes43
- CAN Troubleshooting44
  - CAN Node Off-Line Errors44
Startup, Initial Setup and Setup Wizards45
- Overview45
  - Initial Setup45
- Startup46
  - Touch Screen Calibration47
Chapter 5 Startup, Initial Setup and Setup Wizards47
- Initial Setup Wizard48
- Setup Wizards54
  - Setup Wizard Menu54
- Section Setup Wizard56
  - Using the Section Setup Wizard56
- Product Control Setup Wizard59
  - Using the Product Control Setup Wizard59
- Autoboom™ Setup Wizard62
  - Using the Autoboom™ Setup Wizard62
Chapter 6 Basic Operation63
- Overview63
- Home Screen63
- Job Files67
  - Overview67
- Starting a Job67
  - Setting up a Job68
- Guidance Screen74
- Menu85
- Prescription Maps and Variable Rates94
- System Alarms97
  - Alarms Area97
  - Audible Alarms98
Chapter 7 Tools Menu99
- Wizard Menu100
- System Menu100
- GPS Menu100
- Computer Menu100
- Vehicle Menu101
- Show All101
- Navigation101
- On-Screen Keyboard102
- System Menu103
- Control Interface103
- Product Control108
- Accuboom124
- Autoboom124
- Steering125
- GPS Menu125
- Computer Menu134
- Vehicle Menu139
- Show All147
- Tools Menu99
  - Accessing and Navigating the Tools Menu99
Software Updates and File Maintenance149
- Overview149
- File Maintenance150
  - File Outputs150
  - Performing File Maintenance151
Chapter 8 Software Updates and File Maintenance151
- File Structure153
  - Epro Directory153
- Updates155
  - Applying Software Updates156
Chapter 9 Using Accuboom159
- Accuboom™ Setup160
- Enabling Accuboom164
  - Accuboom™ Modes166
- Using Spray Zone Maps167
- Using Accuboom159
  - Introduction159
    - CAN Switch Box159
Chapter 10 Using Autoboom175
- Ultraglide176
- Autoboom™ Operation176
  - Status Display176
  - Autoboom™ Indicators177
- Using Autoboom175
  - Introduction175
    - Powerglide Plus175
Chapter 11 Troubleshooting179
- Setup Issues180
- Job Issues180
- Coverage Map Issues181
- Error Messages181
  - Job Error Messages181
  - GPS Error Messages182
- CAN Troubleshooting183
- Troubleshooting179
  - Troubleshooting Information179
    - General Issues179
Appendix A Calculating the Calibration Values187
Appendix B Testing Cables199
Appendix C Bogballe Calibrator Zurf Interface201
Appendix D Wireless Communications & Remote Service207
Appendix E Updating CAN Nodes Via the Envizio Pro or Envizio Pro II215
Appendix F Reference of Icons215
Chapter 1 Important Safety Information228
- Limited Warranty231

Raven Envizio Pro - Chapter 4 CAN Networking and Diagnostics

Table of Contents

Other manuals for Raven Envizio Pro

Related product manuals