Roland JUPITER-X - Saving the Tone Settings of each Part (PART1-4 TONE); Initializing the Scene; (Scene Initialize); Initializing a Tone (TONE INITIALIZE)

43
Settings for the Entire Unit
Saving the Tone Settings of Each Part
(PART1–4 TONE)
Here’s how to save the tone settings of each part.
1. Press the [SCENE] button, and then press the [WRITE]
button.
2. Use the [1] knob to select “PART* TONE” (* is the part
to which the tone you’re saving is assigned), and then
press the [ENTER] button.
3. Use the [1] knob or [2] knob to select the save-
destination, and then press the [ENTER] button.
If you want to rename the tone that you’re saving, use the PAGE
[<] [>] buttons to move the cursor, and use the [2] knob to
specify the character.
4. Press the [ENTER] button.
A conrmation message appears.
If you decide to cancel, press the [EXIT] button.
5. To execute, press the [ENTER] button.
Initializing the Scene (SCENE INITIALIZE)
Here’s how to initialize the scene settings.
The rst tone of the presets is selected as the tone for each part.
1. Press the [SCENE] button, and then press the [WRITE]
button.
2. Use the [1] knob to select “SCENE INITIALIZE,” and
then press the [ENTER] button.
Initializing a Tone (TONE INITIALIZE)
Here’s how to initialize the tone of the current part. The initialized state
diers depending on the model that is selected for that part.
You can’t change the model later. You must rst select a tone of the
model that you want to edit, and then execute Tone Initialize to
initialize it.
1. Press the [SCENE] button, and then press the [WRITE]
button.
2. Use the [1] knob to select “TONE INITIALIZE,” and then
press the [ENTER] button.
Editing the System Settings (System)
1. Press the [MENU] button.
2. Use the [1] knob to select “SYSTEM,” and then press
the [ENTER] button.
You can also make this selection by using the PAGE [ ] [ ]
buttons instead of the [1] knob.
3. Use the PAGE [<] [>] buttons to select the page that
you want to edit.
SYSTEM
Make basic device settings for the JUPITER-X.
& “System Parameter List” (p. 44)
SYSTEM EFFECT: Cho
Choose whether the chorus eect settings are xed at the
system settings, or are specied by each scene.
If “Source” is set to “SCENE,” use the scene eect parameters to
edit the eect.
& “Editing a Scene
(SCENE EDIT)” (p. 23)
SYSTEM EFFECT: Dly
Choose whether the delay eect settings are xed at the
system settings, or are specied by each scene.
If “Source” is set to “SCENE,” use the scene eect parameters to
edit the eect.
& “Editing a Scene
(SCENE EDIT)” (p. 23)
SYSTEM EFFECT: Rev
Choose whether the reverb eect settings are xed at the
system settings, or are specied by each scene.
If “Source” is set to “SCENE,” use the scene eect parameters to
edit the eect.
& “Editing a Scene
(SCENE EDIT)” (p. 23)
SYSTEM EQ / COMP
Edit the equalizer and compressor settings.
SYSTEM COLOR SET
Specify the color that is assigned to the buttons.
& “System Parameter List” (p. 44)
4. Use the [1] knob to select the parameter and use the
[2] knob to change the setting.
For details, refer to “Parameter Guide” (PDF).
5. If you want to save the settings, perform the system
write operation.
Saving the System Settings (System Write)
Here’s how to save the system settings.
1. In the SYSTEM screen, press the [WRITE] button.
The SYSTEM WRITE screen appears.
If you decide to cancel, press the [EXIT] button.
MEMO
If the WRITE MENU screen appears, use the [1] or [2] knob to
select “SYSTEM,” and then press the [ENTER] button.
2. To execute, press the [ENTER] button.