Roland V-1HD+ - List of Video Operation Commands

62
RS-232 Command Reference
List of Commands
* When sending a sequence of commands to this unit from a controller, after each one, be sure to verify that an “ack” response is returned before
sending the next command.
Video operations
Item
Sent
command
Response
command
Parameter
Select video source for INPUT 1–4 stxIPS:a,b; ack a =
b =
0 (INPUT 1), 1 (INPUT 2), 2 (INPUT 3), 3 (INPUT 4)
0 (HDMI), 1 (STILL 1), 2 (STILL 2), 3 (STILL 3), 4 (STILL 4)
Select video output from the OUTPUT 1 connector stxOH1:a; ack a = 0 (PGM), 1 (PVW), 2 (Multi-View)
Select video output from the OUTPUT 2 connector stxOH2:a; ack a = 0 (PGM), 1 (PVW), 2 (Multi-View)
Select nal output video stxPGM:a; ack a = 0 (INPUT 1), 1 (INPUT 2), 2 (INPUT 3), 3 (INPUT 4)
Select preview output video stxPST:a; ack a = 0 (INPUT 1), 1 (INPUT 2), 2 (INPUT 3), 3 (INPUT 4)
Select transition eect stxTRS:a; ack a = 0 (MIX), 1 (WIPE)
Set video transition time stxTIM:a; ack a = 0 (0.0 sec)–40 (4.0 sec)
Press the [CUT] button stxCUT; ack
Press the [AUTO] button stxATO; ack
Press the [PinP] button stxP1S; ack
Press the [SPLIT] button stxSPS; ack
Press the [DSK ON] button stxDSK; ack
Press the [DSK PVW] button stxDVW; ack
PinP Adjust position of inset screen stxPP1:a,b;
ack
a =
b =
-500–500 Horizontal position
-500–500 Vertical position
Adjust size of the inset screen. stxPPS:a;
ack
a = 100 (10.0%)–1000 (100.0%)
Adjust zoom ratio of inset screen video stxPPZ:a;
ack
a = 100 (100.0%)–400 (400.0%)
Set the fade-in/out time for the inset screen stxPTM:a;
ack
a = 0 (0.0 sec)–40 (4.0 sec)
Split Adjust position of the video stxSPT:a,b;
ack
When the split composition type is “SPLIT V”
Adjusts the position in the horizontal direction.
a =
b =
-500–500 video on the left (Video on the A/PGM bus)
-500–500 video on the right (Video on the B/PST bus)
When the split composition type is “SPLIT H”
Adjusts the position in the vertical direction.
a =
b =
-500–500 upper video (Video on the A/PGM bus)
-500–500 lower video (Video on the B/PST bus)
Adjust the boundary position stxSCP:a;
ack
a = -500–500
DSK Adjust the key level (amount of extraction) stxKYL:a;
ack
a = 0–255
Adjust the key gain (semi-transmissive region) stxKYG:a;
ack
a = 0–255
Set the fade-in/out time for the source video stxPTM:a;
ack
a = 0 (0.0 sec)–40 (4.0 sec)
Turn the [OUTPUT FADE] knob stxOFD:a;
ack
a = -63–64