Sanyo PLC HF10000L User Manual

27
Basic Operation
For detailed functions of each menu, see “Menu Tree” on pages 82-84.
Main Menu
Sub-Menu
e Image select
For computer source, used to select an image level among Dynamic, Standard, Real, and Image 1-10 (p.39).
For Video source, used to select an image level among Dynamic, Standard, Cinema, and Image 1-10 (p.47).
r Image adjust
For computer source, used to adjust the computer image. [Contrast/Brightness/Color management/Color temp./
White balance (R/G/B)/Offset(R/G/B)/Auto picture control/Advanced color/Sharpness/Gamma/Reset/Store]
(pp.40-42).
For video or HDMI source, used to adjust the video image. [Contrast/Brightness/Color/Tint/Color management/
Color temp./White balance (R/G/B)/Offset (R/G/B)/Auto picture control/Advanced color/Sharpness/Gamma/
Noise Reduction/Progressive/Reset/Store] (pp.48-50).
w PC adjust
Used to adjust the parameters to match with the input signal format (pp.36-38).
t Screen
For computer source, used to adjust the size of the image. [Normal/Full/Wide(16:9)/Zoom/True/Custom/Custom
adj./Digital zoom +/-/Keystone/Ceiling/Rear/Screen aspect/Reset] (pp.43-45).
For video or HDMI source, used to adjust the size of the image. [Normal/Full/Wide(16:9)/Zoom/Natural
wide/Custom/Custom adj./Keystone/Ceiling/Rear/Screen aspect/Reset] (pp. 51-52).
q Input
Used to select an input source (Input 1, Input 2, Input 3, or Input 4) (p.32-34).
u Information
Displays the input source information: Input, H-sync freq., V-sync freq., Screen, Lamp mode, Lamp control, Lamp
interval, Lamp 1, Lamp 2, Language, Filter counter, Power management, Key lock, PIN code lock, Shutter
management, Remote control, SERIAL NO., and Option control No. (p.29).
o Guide
The key operation is displayed.
y Setting
Used to set the projector’s operating configurations (pp.53-68).
i Network
See the owner’s manual of “Network Set-up and Operation”.
Main Menu
q
w
e
r
t
y
u
i
o

Sanyo PLC HF10000L Specifications

General

Matrix size	1.65 \
Matrix type	3-panel (p-Si TFT active)
Projection distance	- m
Vertical scan range	48 - 100 Hz
Horizontal scan range	15 - 120 kHz
Projection technology	LCD
Contrast ratio (typical)	3000:1
Screen size compatibility	- \
Projector native resolution	-
Keystone correction, horizontal	30 °
Interface	USB
Power LED	Yes
RS-232 ports	2
Dimensions (WxDxH)	530 x 757 x 268 mm
Focus	Auto
Focal length range	- mm
Noise level	43 dB
Noise level (economic mode)	39 dB
Dot clock scanning frequency	230 MHz
Lamp power	380 W
Lamps quantity	2 lamp(s)
Light source type	Lamp
Service life of light source	2000 h
Service life of light source (economic mode)	3000 h
Composite video in	0
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
S-Video inputs quantity	1
Wi-Fi	No
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1600 x 1200 (UXGA), 1680 x 1050 (WSXGA+), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product color	Gray
Power consumption (standby)	18 W
Power consumption (typical)	955 W
Cables included	AC, RS-232

Weight and Dimensions

Weight	27600 g