EasyManuals Logo

Sanyo PLC HF10000L User Manual

Sanyo PLC HF10000L
99 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #51 background imageLoading...
Page #51 background image
51
Video Input
Note:
When no signal is detected, Normal is set
automatically and the Aspect dialog box disappears.
The adjustable range for Scale H/V and Position H/V
are limited depending on the input signal.
Natural wide cannot be selected when 720p, 1035i,
1080i or 1080p is selected on AV System Menu (p.46).
1
2
Press the MENU button to display the on-screen
Menu. Use the Point ed buttons to select Screen and
then press the Point 8 or the SELECT button
Use the Point ed buttons to select the desired item
and then press the SELECT button.
Provides the image within a screen size keeping its original
aspect ratio.
Provides the image at the 16:9 wide screen ratio.
Screen Size Adjustment
Scales the image proportionally to fit the entire screen.
Either side of image may go over the screen.
Provides the image to fit full screen size.
Expands the right and left side of images naturally without
changing the center areas.
Provides the last stored aspect screen image.
Adjusts the screen scale and position manually with this
function.
Press the Point 8 button at Custom adj. and the Custom
adjustment menu is displayed on the screen, you can use the
Point ed buttons to choose the item you want to adjust.
Scale H/V ........... Adjusts the Horizontal/Vertical screen
scale.
H&V ................... When set to On, the aspect ratio is
fixed. Scale V appears dimmed and
becomes unavailable. Adjust Scale H,
then the screen scale is automatically
modified based on the aspect ratio.
Position H/V....... . Adjusts the Horizontal/Vertical screen
position.
Common ............ Saves the adjusted scale or position to
all the inputs. Press the SELECT button
at Common to display a confirmation
box. To save the scale or position, press
the SELECT button at "Yes", When
Custom is selected, the saved scale or
position is used.
Reset ................. Resets the all adjusted values. Press
the SELECT button at Reset to display
a confirmation box. To reset, press the
SELECT button at Yes.
Normal
Full
Wide (16:9)
Zoom
Natural wide
Custom
Custom adj.

Table of Contents

Other manuals for Sanyo PLC HF10000L

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo PLC HF10000L and is the answer not in the manual?

Sanyo PLC HF10000L Specifications

General IconGeneral
Matrix size1.65 \
Matrix type3-panel (p-Si TFT active)
Projection distance- m
Vertical scan range48 - 100 Hz
Horizontal scan range15 - 120 kHz
Projection technologyLCD
Contrast ratio (typical)3000:1
Screen size compatibility- \
Projector native resolution-
Keystone correction, horizontal30 °
InterfaceUSB
Power LEDYes
RS-232 ports2
Dimensions (WxDxH)530 x 757 x 268 mm
FocusAuto
Focal length range- mm
Noise level43 dB
Noise level (economic mode)39 dB
Dot clock scanning frequency230 MHz
Lamp power380 W
Lamps quantity2 lamp(s)
Light source typeLamp
Service life of light source2000 h
Service life of light source (economic mode)3000 h
Composite video in0
Serial interface typeRS-232
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
S-Video inputs quantity1
Wi-FiNo
Analog signal format systemNTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions1024 x 768 (XGA), 1280 x 1024 (SXGA), 1600 x 1200 (UXGA), 1680 x 1050 (WSXGA+), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product colorGray
Power consumption (standby)18 W
Power consumption (typical)955 W
Cables includedAC, RS-232
Weight and Dimensions IconWeight and Dimensions
Weight27600 g

Related product manuals