How to troubleshoot F08700 fault in Siemens Media Converter?
To address the F08700 fault on your Siemens Media Converter, check the bus cable, baud rate (p8622), and bit timing (p8623). Also, verify the master. After resolving the cause of the fault, manually start the CAN controller with p8608 = 1.
How to troubleshoot 'Converter overtemperature' on Siemens Control Unit?
To address a converter overtemperature issue on your Siemens Control Unit, check if the converter fan is running and ensure the ambient temperature is within the permissible range. Also, check if the motor is overloaded and consider reducing the pulse frequency.
What to do if Siemens SINAMICS G120D shows F30004 error?
To troubleshoot the F30004 fault on your Siemens Media Converter, start by checking if the converter fan is running and ensure the ambient temperature is within the allowed range. Also, verify that the motor isn't overloaded and consider reducing the pulse frequency.
How to fix F07801 fault on Siemens SINAMICS G120D?
To resolve the F07801 fault in your Siemens Media Converter, review the current limits (p0640). For U/f control, check the current limiting controller (p1340 … p1346). You can also increase the acceleration ramp (p1120) or reduce the load. Inspect the motor and motor cables for short circuits and ground faults. Verify the motor's star-delta connection and rating plate parameterization. Ensure the power unit and motor combination are correct. If switching to a rotating motor, select the flying restart function (p1200).
What to do if my Siemens Media Converter displays 'Temperature sensor fault'?
If your Siemens Media Converter displays a 'Temperature sensor fault', check that the sensor is connected correctly.
What to do if Siemens Media Converter displays 'Motor overspeed'?
If your Siemens Media Converter displays 'Motor overspeed', activate precontrol of the speed limiting controller and increase hysteresis for the overspeed signal.
What to do if Siemens SINAMICS G120D displays 'Motor stalled'?
If your Siemens Media Converter indicates that the motor is stalled, verify that the motor data has been correctly parameterized and perform motor identification. Also, check the current limits.
What to do if Siemens Media Converter shows 'I2t Motor Module overtemperature'?
If your Siemens Media Converter displays 'I2t Motor Module overtemperature', check and reduce the motor load if necessary, verify the motor's ambient temperature, check the thermal time constant, and inspect the overtemperature fault threshold.
What to check if Siemens SINAMICS G120D Media Converter displays 'Motor temperature sensor alarm'?
If your Siemens Media Converter displays a 'Motor temperature sensor alarm', check that the sensor is connected correctly and verify the parameter assignment.
What to do if Siemens Media Converter displays 'Motor temperature sensor fault'?
If the Siemens Media Converter displays a 'Motor temperature sensor fault', ensure the sensor is correctly connected, verify the parameterization, or deactivate the temperature sensor fault.
General| Brand | Siemens |
|---|---|
| Model | SINAMICS G120D |
| Category | Media Converter |
| Language | English |
Essential safety guidelines for operating electrical devices and preventing hazards.
Provides essential guidelines for electrical connections, including line supplies and EMC rules.
Outlines the steps for performing basic commissioning using the STARTER software tool.
Details the setup and function of the fail-safe digital input for STO safety.
Covers communication setup, functions, and requirements for PROFINET integration.
Details requirements, integration, and configuration for PROFIBUS communication.
Explains how to switch the motor on/off and manage converter states and commands.
Describes the EPOS function, operating modes, commissioning, and configuration of positioning.
Explains the STO safety function, its principle of operation, and commissioning procedures.
Details how the inverter signals faults, the fault buffer, and how to acknowledge and delete faults.
Details recommended procedures for testing safety functions and documenting results.
To Next Page