Siemens SINUMERIK 808D ADVANCED Parameter Manual

SEARCH_RUN_MODE
11450, 70
SERUPRO_SYNC_MASK
42125, 310
SERVO_DISABLE_DELAY_TIME
36620,
291
SIEM_TRACEFILES_CONFIG
11294, 64
Signals at fast inputs and outputs, 467
Signals from axis/spindle, 426, 427, 443, 444, 445,
446, 447, 448
Signals from fast inputs and outputs, 468
Signals from maintenance planners, 461
Signals from MCP, 453
Signals from NC channel, 472
Signals from operator panel, 461
Signals from PLC, 460
Signals from the HMI, 459
Signals to axis/spindle, 476
Signals to maintenance planners, 460
Signals to MCP, 454
Signals to NC channel, 469
Signals, synchronized actions from channel, 483
Signals, synchronized actions to channel, 483
SIMU_AX_VDI_OUTPUT
30350, 216
SINAMICS_ALARM_MASK
13150, 81
SINAMICS_IBN_TIMEOUT_VALUE
1091, 21
SINAMICS_MAX_SLAVE_ADDRESS
13160, 81
Singlas from axis/spindle, 478
SINGLEBLOCK2_STOPRE
42200, 312
SLASH_MASK
10706, 42
SMOOTH_CONTUR_TOL
42465, 315
SMOOTH_ORI_TOL
42466, 315
SMOOTHING_MODE
20480, 147
SOFT_ACCEL_FACTOR
32433, 240
SOFTKEY_CENTRE_ADJ
1106, 23
Special bit memory SM bit definition (read-only), 452
SPF_END_TO_VDI
20800, 160
SPIND_ACTIVE_AFTER_RESET
35040, 271
SPIND_ASSIGN_TO_MACHAX
35000, 267
SPIND_CONSTCUT_S
43202, 342
SPIND_DEF_MASTER_SPIND
20090, 113
SPIND_DEFAULT_ACT_MASK
35030, 269
SPIND_DEFAULT_MODE
35020, 268
SPIND_DES_VELO_TOL
35150, 276
SPIND_EXTERN_VELO_LIMIT
35160, 277
SPIND_FUNC_RESET_MODE
35032, 269
SPIND_FUNCTION_MASK
35035, 269
SPIND_MAX_VELO_G26
43220, 343
SPIND_MAX_VELO_LIMS
43230, 344
SPIND_MIN_VELO_G25
43210, 343
SPIND_ON_SPEED_AT_IPO_START
35500, 282
SPIND_OSCILL_ACCEL
35410, 280
SPIND_OSCILL_DES_VELO
35400, 280
SPIND_OSCILL_START_DIR
35430, 281
SPIND_OSCILL_TIME_CCW
35450, 281
SPIND_OSCILL_TIME_CW
35440, 281
SPIND_POSCTRL_VELO
35300, 279
SPIND_POSIT_DELAY_TIME
35310, 279
SPIND_POSITIONING_DIR
35350, 280
SPIND_RIGID_TAPPING_M_NR
20094, 113
SPIND_S
43200, 342
SPIND_SPEED_TYPE
43206, 342
SPIND_STOPPED_AT_IPO_START
35510, 282
SPIND_USER_VELO_LIMIT
43235, 344
Index
Parameter Manual
Parameter Manual, 08/2015, 6FC5397-8EP40-0BA1 513

Siemens SINUMERIK 808D ADVANCED Specifications

General

Brand	Siemens
Model	SINUMERIK 808D ADVANCED
Category	Control Unit
Language	English