Siemens SINUMERIK 808D User Manual

Programming and Operating Manual (Milling)
6FC5398-4DP10-0BA6, 09/2017
5
9.1 Executing a part program.....................................................................................................................................46
9.2 Executing specified blocks...................................................................................................................................47
9.3 Correcting a part program ....................................................................................................................................48
9.4 Simultaneous recording during machining of the workpiece..........................................................................48
9.5 Entering the tool wear offsets ..............................................................................................................................49
10 Other common operations .................................................................................................................... 53
10.1 Program control functions ....................................................................................................................................53
10.1.1 Program test...........................................................................................................................................................53
10.1.2 Dry run feedrate.....................................................................................................................................................53
10.1.3 Conditional stop .....................................................................................................................................................53
10.1.4 Skip block ...............................................................................................................................................................53
10.1.5 Single block mode .................................................................................................................................................53
10.1.6 Rapid traverse override ........................................................................................................................................54
10.1.7 Auxiliary function lock ...........................................................................................................................................54
10.2 Calibrating the tool probe .....................................................................................................................................54
10.3 Measuring the tool with a probe (auto) ..............................................................................................................56
10.4 Setting up the workpiece ......................................................................................................................................57
10.4.1 Measuring the workpiece .....................................................................................................................................57
10.4.2 Entering/modifying workpiece offsets ................................................................................................................59
10.5 Entering/modifying the setting data ....................................................................................................................60
10.6 Setting R parameters ............................................................................................................................................63
10.7 Setting user data ...................................................................................................................................................64
10.8 Setting the date and time .....................................................................................................................................64
10.9 Configuring the operating area after startup .....................................................................................................65
10.10 Executing/transferring a part program from external .......................................................................................65
10.10.1 Executing/transferring through the USB interface............................................................................................65
10.10.1.1 Executing from external (through USB interface) ............................................................................................66
10.10.1.2 Transferring from external (through USB interface) ........................................................................................67
10.10.2 Executing/transferring through the Ethernet connection.................................................................................67
10.10.2.1 Configuring the network drive..............................................................................................................................67
10.10.2.2 Executing from external (through Ethernet connection)..................................................................................70
10.10.2.3 Transferring from external (through Ethernet connection)..............................................................................70
10.10.3 Configuring the firewall .........................................................................................................................................71
10.11 Extending/deactivating the CNC lock function..................................................................................................72
10.12 Data backup ...........................................................................................................................................................74
10.12.1 Internal data backup .............................................................................................................................................74
10.12.2 External data backup ............................................................................................................................................75
10.12.2.1 External data backup in a data archive..............................................................................................................75
10.12.2.2 External data backup of separate files...............................................................................................................76
10.13 Pocket calculator ...................................................................................................................................................77
11 Programming principles........................................................................................................................ 78
11.1 Fundamentals of programming ...........................................................................................................................78
11.1.1 Program names .....................................................................................................................................................78
11.1.2 Program structure..................................................................................................................................................79
11.2 Programming instructions ....................................................................................................................................79
11.2.1 Programming dimensions ....................................................................................................................................79
11.2.2 Plane selection: G17 to G19................................................................................................................................80
11.2.3 Absolute/incremental dimensioning: G90, G91, AC, IC ..................................................................................81
11.2.4 Dimensions in metric units and inches: G71, G70, G710, G700 ...................................................................82
11.2.5 Polar coordinates, pole definition: G110, G111, G112....................................................................................82
11.2.6 Programmable work offset: TRANS, ATRANS.................................................................................................84
11.2.7 Programmable rotation: ROT, AROT .................................................................................................................85
11.2.8 Programmable scale factor: SCALE, ASCALE ................................................................................................86
11.2.9 Programmable mirroring: MIRROR, AMIRROR ...............................................................................................87
11.2.10 Workpiece coordinate system - settable work offset: G54 to G59, G500, G53, G153 ..............................88

Siemens SINUMERIK 808D Specifications

General

Brand	Siemens
Model	SINUMERIK 808D
Category	Control Unit
Language	English