Index
NC/PLC Interface Signals (Z1)
Function Manual, 08/2005 Edition, 6FC5397-0BP10-0BA0
Index-5
Feed rate override active, 2-139
Feed rate override selected for rapid traverse,
2-140
Feed stop (Geometry axis 1 to 3), 2-139
Feed stop/spindle stop (axis-specific), 2-146
Fixed stop reached, 2-73
Follow-up mode active, 2-42
Follow-up operation, 2-29
Gear is changed over, 2-120
Hardware limit switches plus and minus, 2-68
Heatsink temperature prewarning, 2-55
Higraph first error display, 2-10
i2t monitoring, 2-63
Interface signals: Activate machine-related
protection zone, 2-64
Interface signals: Enable protection zones, 2-64
Interrupt processing active, 2-104
Invert M3/M4, 2-122
JOG mode, 2-81
Key disable, 2-8
Key-operated switch position, 2-1
Last action block active, 2-98
Load, 2-23
Load part program, 2-14
Lubrication pulse, 2-46
M fct. 1-5 not included in list, 2-75
M function for spindle, 2-132
M(d) less than M(dx), 2-57
M, S, T, D, H, F functions Additional info "Quick"
(quick acknowledgment), 2-75
M, S, T, D, H, F functions Modification, 2-74
M00/M01 active, 2-97
M02/M30 active, 2-99
Machine function REF, 2-84
Machine function REPOS, 2-83
Machine function TEACH IN, 2-83
Machine-related protection zone preactivated, 2-65
Machine-related protection zone violated, 2-66
MDA mode, 2-80
MMC alarm is active, 2-2
MMC CPU1 Ready, 2-4
MMC CPU2 Ready (to OPI or MPI), 2-4
MMC temperature limit, 2-2
MMC101/102 battery alarm, 2-3
Mode change disable, 2-16
Mode changeover inhibit, 2-81
Mode group number, 2-24
Mode group ready, 2-88
Mode group reset, 2-82
Mode group stop, 2-82
Mode group stop axes plus spindles, 2-82
Motor selection A, B, 2-39
Motor selection in progress, 2-40
Motor temperature pre-warning, 2-53
n(act) equals n(set), 2-60
n(act) less than n(min), 2-59
n(act) less than n(x), 2-59
NC Ready, 2-5
NC start, 2-94
NC start disable, 2-93
NC stop, 2-95
NC Stop at block limit, 2-94
NC Stop axes plus spindles, 2-95
NCK alarm is active, 2-5
NCK alarm with processing stop present, 2-26
NCK battery alarm, 2-7
NCK CPU Ready, 2-3
NCU 573 heatsink temperature alarm, 2-6
OK, 2-19, 2-22
Oscillation controlled by the PLC, 2-124
Oscillation speed, 2-123
Override active, 2-145
Overstore active:DB21 DBX318.7, 2-26
Path axis, 2-112
PLC action completed, 2-91
PLC index, 2-14, 2-15
PLC line offset, 2-15, 2-16
Position controller active, 2-43
Position measuring systems 1 and 2, 2-31
Position reached with exact stop coarse, 2-70
Position reached with exact stop fine, 2-70
PROG-EVENT-DISPLAY, 2-109
Program level abort, 2-93
Program status aborted, 2-102
Program status interrupted, 2-102
Program status running, 2-101
Program status stopped, 2-102
Program status wait, 2-101
Program test active, 2-100
Programming area selection, 2-10
Pulse enable, 2-41
Pulses enabled, 2-51
Ramp-function generator fast stop, 2-36
Ramp-function generator fast stop active, 2-46
Ramp-up completed, 2-55
Ramp-up times, 2-36
Rapid traverse override, 2-136
Rapid traverse override active, 2-138
Read-in disable, 2-93
Read-in enable is ignored, 2-104
Recall alarm cleared, 2-18
Reference point approach delay, 2-117
Reference point value 1 to 4, 2-117
Referenced/synchronized 1, 2-118
Referenced/synchronized 2, 2-118
Referencing active, 2-116
Repos DEFERAL Chan, 2-109
REPOS Delay Ackn, 2-111
To Next Page
Loading...
Need help?
General
