SIGLENT SDS1202X-E

To Next Page

To Previous Page

SDS1000X-E&SDS1000X-U User Manual

WWW.SIGLENT.COM

Note: You can force the oscilloscope to trigger by pressing the Single button

twice. The trigger status in the upper left corner of the screen will be displayed

as "FStop".

 To capture single event or a periodic signal.

 To capture burst or other unusual signals.

Main Page

Safety Terms and Symbols6
Measurement Category7
Working Environment8
General Care and Cleaning10
Résumé Général de Sûreté12
Limites Et Symboles de Sûreté14
Catégorie de Mesure15
Environnement de Fonctionnement16
Condition de Ventilation18
Soin Général Et Nettoyage21
Document Overview23
Table of Contents24
Quick Start33
- General Inspection34
- Appearance and Dimensions35
- Prepare for Using37
- Front Panel Overview41
- Rear Panel Overview44
- Front Panel Function Overview47
- Help54
- User Interface55
- Security Lock58
Vertical System59
- Enable the Channel60
- Adjust Scale61
- Vertical Position62
- Coupling62
- Bandwidth Limit63
- Probe63
- Unit64
- Deskew64
- Invert64
- Trace Visible/Hidden65
Horizontal System66
- Horizontal Scale67
- Trigger Delay68
- Roll Mode69
- Zoom Mode70
Sample System72
- Run Control73
- Overview74
- Memory Depth77
- Sampling Mode77
- Interpolation Method78
- Acquisition Mode81
- Horizontal Format86
- Sequence Mode88
Trigger90
- Trigger Source92
- Trigger Mode93
- Trigger Level95
- Trigger Coupling96
- Trigger Holdoff97
- Noise Rejection98
- Trigger Type100
Serial Trigger and Decode122
- I2C Trigger and Serial Decode123
- SPI Trigger and Serial Decode130
- UART Trigger and Serial Decode137
- CAN Trigger and Serial Decode142
- LIN Trigger and Serial Decode147
Reference Waveform152
- Save REF Waveform to Internal Memory153
- Display REF Waveform153
- Adjust REF Waveform154
- Clear REF Waveform154
Math156
- Units for Math Waveforms157
- Math Operators158
Cursors171
- Y Cursors171
- Make Cursor Measurements173
Measure175
- Type of Measurement176
- Automatic Measurement180
- All Measurement182
- Gate Measurement183
- Clear Measurement183
Display184
- Display Type185
- Color Display186
- Persistence187
- Clear Display188
- Grid Type188
- Intensity188
- Grid Brightness189
- Transparence189
Save and Recall191
- Save Type192
- Internal Save and Recall194
- External Save and Recall195
- Disk Management198
Digital Channels(Option)201
- Connect the Digital Probes202
- Acquire Digital Waveform203
- Digital Channels Height203
- Digital Channels Position204
- Single Digital Channel204
- All Digital Channels205
- Logic Threshold205
- Digital Bus206
- Deskew207
- System Setting208
  - System Status208
- Remove Device209
System Setting210
- View System Status211
- Do Self Cal211
- Quick-Cal213
- Sound213
- Language213
- Pass/Fail Test214
  - Set and Perform Pass/Fail Test214
  - Save and Recall Test Mask215
- Arbitrary Waveform Generator(Option)218
- IO Set225
- Web Server228
- Update Firmware and Configuration229
- Do Self-Test230
  - Keyboard Test231
  - LED Test231
- Screen Saver233
- Reference Position234
- Power on Line234
- Option Management235
Bode Plot II237
- Perform Bode Plot237
- Setting237
- Example241
  - Simple Sweep Operation241
  - Vari-Level Sweep Operation243
Search246
- Setting246
- Results247
Navigate249
- Time Navigate249
- History Frame Navigate249
- Search Event Navigate250
History251
Factory Setup253
Troubleshooting254

SIGLENT SDS1202X-E - Page 94

Table of Contents

Other manuals for SIGLENT SDS1202X-E

Related product manuals