SUBARU SELECT MONITOR
ENGINE (DIAGNOSTICS)
Contents
7.
LED OPERATION MODE
FOR
ENGINE
1)
On the ((Main Menu,, display screen, select the {Each System Check} and press the [YES] key.
2)
On the ((System Selection Menu)) display screen, select the {Engine Control System} and press the [YES]
key.
3)
Press the [YES] key after displayed the information of engine type.
4) On the ((Engine Diagnosis), display screen, select the {Current Data Display
&
Save} and press the [YES]
key.
5)
On the <<Data Display Menu)) display screen, select the {Data
&
LED Display} and press the [YES] key.
6)
Using the scroll key, move the display screen up or down until the desired data is shown.
A list of the support data is shown in the following table.
Display
I
Message
1
LED "ON" requirements
lanition switch signal
Test mode connector signal
Neutral position switch signal
Air conditioning switch sianal
.-
Ignition Switch
Test Mode Signal
Neutral Position Switch
NC Switch
ON or OFF When ignition switch is turned
ON.
ON
or OFF
When test mode connector is connected.
ON or OFF When neutral position signal is entered.
"
I
W.l".,
ni-...-.l
A
/P
Prrmnrrrr.r.nv
Cinn-l
orOFF When air conditioning switch is turned
ON.
When air conditioning compressor is in func-
ON or OFF
tion,
Radiator main fan relay signal
Knocking signal
Radiator sub fan relay signal
..-.-I
u4
..
Radiator Fan Relay
#1
Knocking Signal
ON
or OFF When knocking signal is entered.
Radiator Fan Relay
#2
ON or OFF When radiator main fan relay is in function.
ON or OFF When radiator sub fan relay is in function.
When engine torque control signal
1
is
T-r-.
.-
P..-+..nl
CL-.nnl
u.4
ON
Or
OFF
entered.
Engine torque control signal
#2
When engine torque control signal
2
is
1
ON
Or
OFF
1
entered.
Torque Control Signal
#2
When camshaft position sensor signal is
entered.
Camshaft position sensor signal
1
Camshaft Position Signal
1
ON
or OFF
I
Engine torque control permission
sianal
Torque
Control
Permission
When engine torque control permission sig-
nal is entered.
ON
Or
OFF
-
I
I I
Liaht switch sianal
I
LiQht Switch
1
ON
or OFF
I
When small light switch is turned ON.
Rear oxygen sensor rich signal Rear
02
Rich Signal
ON
or OFF
When rear oxygen sensor mixture ratio is
rich,
Starter switch signal
Idle switch signal
Crankshaft position sensor signal
NOTE:
For detailed operation procedure, refer
to
the SUBARU SELECT MONITOR OPERATION MANUAL.
Starter Switch
Idle Switch Signal
Crankshaft Position Signal ON or OFF
entered,
ON
or
OFF When starter switch signal
is
entered.
ON
or
OFF When idle switch signal is entered.
When crankshaft position sensor signal is
EN(D0HC TURBO)-43
Power steering switch signal
Rear defogger switch signal
Blower fan switch sianal
PIS Switch
Rear Defogger Switch
Blower Fan Switch
ON or OFF When power steering switch is entered.
ON
or OFF When rear defogger switch
is
turned
ON.
ON
or OFF When blower fan switch is turned ON.
~
Tumble generator valve actuator
signal
Tumble generator valve drive sig-
nal
ON
or OFF When TGV actuator signal is entered.
OPEN
Or
When TGV moves and valve opens.
CLOSE
TGV
Output
TGV
Drive
Fuel pressure control solenoid
valve signal
Drain valve signal
pcv
Solenoid
Valve
Vent. Solenoid Valve
When fuel pressure control solenoid valve is
ON
Or
OFF in function.
ON or OFF When drain valve is in function.
To Next Page
Loading...
