Technogym RUN 600 XTPRO - Page 7

RUN 600 XTPRO: Service & Maintenance Manual - rev. 1.3
Page iii
9. CONFIGURING THE MACHINE.......................................................................................................................9.1
9.1. USER SETTING PARAMETERS .............................................................................................................................9.1
9.1.1. Language used......................................................................................................................................9.1
9.1.2. Measurement system .............................................................................................................................9.2
9.1.3. Maximum time ......................................................................................................................................9.2
9.1.4. Activating the “+” and “ − ” keys .........................................................................................................9.2
9.1.5. Disabling the function keys...................................................................................................................9.2
9.1.6. Enabling the “ENTER” key..................................................................................................................9.3
9.1.7. Setting the priority ................................................................................................................................9.3
9.2. TECHNICAL SETTING PARAMETERS ...................................................................................................................9.3
9.2.1. Enabling use of the hand sensor...........................................................................................................9.4
9.2.2. Enabling the display mode ...................................................................................................................9.4
9.3. MAINTENANCE INFORMATION ...........................................................................................................................9.4
9.3.1. Hours on ...............................................................................................................................................9.4
9.3.2. Hours of use of the belt motor ..............................................................................................................9.5
9.3.3. Minutes of use of the evelation motor...................................................................................................9.5
9.3.4. Distance covered ..................................................................................................................................9.5
9.4. CHANGING THE MAINTENANCE INFORMATION...................................................................................................9.5
9.4.1. Hours on ...............................................................................................................................................9.5
9.4.2. Hours of use of the belt motor ..............................................................................................................9.5
9.4.3. Minutes of use of the evelation motor...................................................................................................9.6
9.4.4. Distance covered ..................................................................................................................................9.6
9.5. PROGRAMMING THE HITACHI SJ100 INVERTER .............................................................................................9.7
9.5.1. Monitor function parameters................................................................................................................9.8
9.5.2. Modified parameter settings .................................................................................................................9.8
9.6. PROGRAMMING THE HITACHI J100 INVERTER................................................................................................9.9
10. SCHEDULED MAINTENANCE........................................................................................................................10.1
10.1. EXTERNAL CLEANING OPERATIONS .................................................................................................................10.1
10.1.1. Setting up the operation......................................................................................................................10.1
10.1.2. Cleaning operations ...........................................................................................................................10.1
10.1.3. Lubricating the tread belt ...................................................................................................................10.1
10.2. ROUTINE MAINTENANCE OPERATIONS.............................................................................................................10.2
10.2.1. Internal cleaning operations...............................................................................................................10.2
10.2.2. Lubricating the elevation bars............................................................................................................10.2
10.2.3. Checking the state of wear..................................................................................................................10.2
10.2.4. Checking and centering the tread belt................................................................................................10.3
10.2.5. Checking the emergency button..........................................................................................................10.3
10.3. SPECIAL MAINTENANCE OPERATIONS ..............................................................................................................10.4
10.3.1. Carrying out the routine maintenance procedure ..............................................................................10.4
10.3.2. Checking the working conditions........................................................................................................10.4
10.3.3. Checking the wiring and connections.................................................................................................10.4
10.3.4. Checking the display...........................................................................................................................10.4
10.3.5. Checking the wear of the motor roller................................................................................................10.4
10.3.6. Checking the wear of the rear roller...................................................................................................10.5
10.3.7. Checking the wear of the rubber handlebar covers............................................................................10.5
10.3.8. Checking the tread belt motor drive-belt............................................................................................10.5
10.3.9. Checking the elevation motor drive-belt.............................................................................................10.5
10.3.10. Checking the shock absorbers .........................................................................................................10.5
10.3.11. Checking the speed calibration........................................................................................................10.5
10.3.12. Checking the operation of the cardio receiver.................................................................................10.5
10.3.13. Checking the operation of the hand sensor receiver........................................................................10.6
11. APPENDIX ...........................................................................................................................................................11.1
11.1. TECHNICAL NOTES ON CARDIO RECEIVERS......................................................................................................11.1
11.1.1. Type of ASIC.......................................................................................................................................11.2
11.1.2. Presence of electromagnetic fields .....................................................................................................11.2
11.1.3. Reducing receiver sensitivity ..............................................................................................................11.3