Toshiba E-STUDIO2008A - Page 19

© 2015 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2008A/2508A/3008A/3508A/4508A/5008A
CONTENTS
7
6.6.6 Fine adjustment of black density .....................................................................6-36
6.6.7 RGB conversion method selection ..................................................................6-36
6.6.8 Adjustment of saturation..................................................................................6-36
6.6.9 Background offsetting adjustment for RADF ...................................................6-37
6.6.10 Adjustment of the capacity and image quality of SlimPDF ..............................6-37
6.6.11 Surrounding void amount adjustment..............................................................6-38
6.6.12 JPEG compression level adjustment............................................................... 6-38
6.6.13 RADF scan noise reduction (Scanning Function)............................................6-39
6.7 Image Quality Adjustment (FAX Function)...................................................................... 6-40
6.7.1 Density adjustment ..........................................................................................6-40
6.7.2 Adjustment of image density............................................................................6-41
6.8 Adjustment of High-Voltage Transformer........................................................................6-42
6.8.1 Adjustment.......................................................................................................6-42
6.8.2 Precautions......................................................................................................6-48
6.9 Scanner...........................................................................................................................6-50
6.9.1 Adjustment carriages-1 positions.....................................................................6-50
6.9.2 Position adjustment of CCD lens unit ..............................................................6-51
6.9.3 Belt tension adjustment of the Scan motor......................................................6-51
6.10 Adjustment of the Paper Feeding System.......................................................................6-52
6.10.1 Sheet sideways deviation caused by paper feeding........................................6-52
6.11 Adjustment of Developer Unit .........................................................................................6-55
6.11.1 Doctor-to-sleeve gap .......................................................................................6-55
6.12 Adjustment of the RADF .................................................................................................6-58
6.12.1 Adjustment of RADF position...........................................................................6-58
6.12.2 Adjustment of RADF height .............................................................................6-62
6.12.3 Adjustment of skew..........................................................................................6-64
6.12.4 Adjustment of the leading edge position..........................................................6-67
6.12.5 Adjustment of horizontal position.....................................................................6-69
6.12.6 Adjustment of copy ratio ..................................................................................6-70
6.13 Adjustment of the Inner Finisher .....................................................................................6-71
6.13.1 Alignment position adjustment......................................................................... 6-71
6.13.2 Stapling position adjustment............................................................................ 6-71
6.13.3 Punching position center adjustment...............................................................6-72
6.13.4 Punch hole position adjustment.......................................................................6-73
6.14 Adjustment of the Console Finisher ................................................................................6-74
6.14.1 Adjusting the alignment position......................................................................6-74
6.14.2 Adjusting the stapling position .........................................................................6-76
6.14.3 B4-size recycled paper mode settings.............................................................6-78
6.14.4 Adjusting Paper Exit Speed.............................................................................6-80
6.15 Adjustment of the Saddle Stitch Finisher ........................................................................6-87
6.15.1 Adjusting the Alignment Position .....................................................................6-87
6.15.2 Adjusting the Stapling Position ........................................................................6-90
6.15.3 Stapling/folding position adjustment in saddle stitch unit.................................6-92
6.15.4 Saddle Stitch Skew Adjustment.......................................................................6-98
6.16 Adjustment of Hole punch unit ........................................................................................6-99
6.16.1 Destination setting of hole punch control PC board.........................................6-99
7. PREVENTIVE MAINTENANCE (PM)............................................................................7-1
7.1 General Description ..........................................................................................................7-1
7.2 PM Display........................................................................................................................7-1
7.2.1 General description............................................................................................ 7-1
7.2.2 PM display conditions........................................................................................7-1
7.2.3 PM display contents........................................................................................... 7-3
7.2.4 Clearing counter ................................................................................................7-3
7.3 General Descriptions for PM Procedure ...........................................................................7-4
7.4 PM Support Mode (6S) .....................................................................................................7-5
7.4.1 General description............................................................................................ 7-5
7.4.2 Operational flow and operational screen ...........................................................7-5
7.4.3 Work flow of parts replacement .......................................................................7-10