Tynetec Advent xt - Page 52

DocNo.FM0410issueM‐1Page52
32.KIRK400MULTICELLDECT

MATRIX CONNECTION

TheMatrixIPPBXinterfacestheAdventxttotheDECT;italsogivesaccesstoanoutsidelineandallowszoningofcalls.

24VDC‐connecttotheUPSviathein‐linePSUmoduleprovided. 
CO1‐connecttotheAdventxtDECToutputusingtheRJ11/BTleadprovided.
CO2‐connecttoanexternallineusingthesecondRJ11/BTleadprovided.
SLT1‐connecttothefixedCLIdesktelephoneviaaBTmastersocket(Note:cutoneplugofftheRJ11/RJ11leadprovided).
ETHERNET‐connecttotheFastswitchPort9usingtheRJ45patchleadprovided.
‐connecttoasoundEarthterminalusingtheEarthwireprovided

TheMatrixisfactoryprogrammedsoallincominglinesringallextensions.Ifanincominglineistoringspecificextensions
thentheMatrixmustbereconfigured.

Note;intheeventofamainsfailurei.e.iftheUPSbatteriesrunflatorifaUPSisnotfitted,theMatrixconnectsCO1toSLT1
andtheAdventxtwillonlyringthefixedCLIdesktelephone.

KIRK 400 WIRELESS SERVER (MULTI CELL) PROGRAMMING

TheMatrixmusthaveitsIPaddresssetto192.168.0.2
TheKirk400WirelessServermusthaveitsIPaddresssetto192.168.0.3anditsRadioPartNumbersetto3.
AdditionalIP12ChannelBaseStationsmustIPaddressesset192.168.0.4/5/6andRadioPartNumbers4/5/6.

ADVENT xt PROGRAMMING

ThePBXRingmustbeenabledinthe“GeneralSetup”programming‐seetheAdventxtProgrammingManual(TynetecDoc
No.FM0411).

2 CHANNEL MULTI CELL REPEATERS

Amaximumofthree2ChannelMultiCellRepeaterscanbeconnectedtotheKirk400MultiCellWirelessServerplusthree
perIP12ChannelBaseStation(total12persite).Repeatersrequireapowerconnectiononly;theycommunicatewiththe
Server/BaseStationvialowpowerradiosignalsanddonotrequirealineconnection.TomaintainDECTcoverageduringa
mainsfailureallRepeatersmustbeconnectedtoabatterybacked12VDCPSU.SeeRepeaterDeploymentRulesonthe
followingpage.

REPEATER POSITIONING

BeforeinstallingpowercablestoRepeaterpositionsitisimportantthattheoptimumpositionforcoverageisestablished.
RegistertheRepeaterontotheWirelessServer/IPBase(seeKirkProgrammingKitbelow)thenwiththeRepeaterpowered
fromabatterywalkawayinthedirectionthatcoveristobeextended.WhentheredLEDontheRepeaterstartstoflashit
isoutofrangeandmustbemovedbacktowardstheWirelessServer/IPBasebyaminimumof5metresbeforeselectingits
finallocation.

REPEATER PROGRAMMING

AKirkProgrammingKit(P/No.ZCS729)isrequiredtoprogramRepeaters,thekitconsistsofadoubleadapterandcomms
lead–thelatestServiceToolPCsoftwareanduserguidecanbedownloadedfreeofchargefrom;
http://support.polycom.com/PolycomService/support/us/support/voice/dect/dect_base_stations.html

REPEATER POWER CONNECTION

Repeatersshouldbeconnectedusing 1.0mmpaircabling,ifCW1308isbeingusedthensparepairscanbe doubled ‐up
and/orloopedbacktoformaringcircuittoreducethevoltagedrop.














TypicallythemaximumdistancetoaRepeaterviaCW1308shouldnotexceed100metres.
Note:connecta
maximumof6Repeatersper12V2APSU.
Maximum12x2ChannelMultiCellRepeaters
(3perMultiCellWirelessServer+3perIP12ChannelBaseStation)
240V
AC
12VDCPSUincluding
Standb
y
Batter
y

RepeaterPowerLeadColourCode
YELLOW=12VBLACK=0V
Use1.0mmCable
Max100m