Ublox SARA-R4 Series - Page 125

SARA-R4/N4 series-AT Commands Manual
UBX-17003787 - R09

13Packet switched data services
Page 125 of 307
Parameter Type Description
o 0 (factory-programmed value): subscribed
o 1: class 1
o 2: class 2
o 3: class 3
o 4: best effort
• 12: QoS reliability - the <param_val> parameter selects the reliability class:
o 0 (factory-programmed value): subscribed
o 1: class 1 (Interpreted as class 2)
o 2: class 2 (GTP Unack, LLC Ack and Protected, RLC Ack)
o 3: class 3 (GTP Unack, LLC Unack and Protected, RLC Ack)
o 4: class 4 (GTP Unack, LLC Unack and Protected, RLC Unack)
o 5: class 5 (GTP Unack, LLC Unack and Unprotected, RLC Unack)
o 6: class 6 (Interpreted as class 3)
• 13: QoS peak rate - the <param_val> parameter selects the peak throughput in
range 0-9. The factory-programmed value is 0.
• 14: QoS mean rate - the <param_val> parameter selects the mean throughput in
range 0-18, 31. The factory-programmed value is 0.
• 15: minimum QoS precedence - the <param_val> parameter selects the acceptable
value for the precedence class:
o 0 (factory-programmed value): subscribed
o 1: high
o 2: normal
o 3: low
• 16: minimum QoS delay - the <param_val> parameter selects the acceptable value
for the delay class:
o 0 (factory-programmed value): subscribed
o 1: class 1
o 2: class 2
o 3: class 3
o 4: best effort
• 17: minimum QoS reliability - the <param_val> parameter selects the minimum
acceptable value for the reliability class:
o 0 (factory-programmed value): subscribed
o 1: class 1 (Interpreted as class 2)
o 2: class 2 (GTP Unack, LLC Ack and Protected, RLC Ack)
o 3: class 3 (GTP Unack, LLC Unack and Protected, RLC Ack)
o 4: class 4 (GTP Unack, LLC Unack and Protected, RLC Unack)
o 5: class 5 (GTP Unack, LLC Unack and Unprotected, RLC Unack)
o 6: class 6 (Interpreted as class 3)
• 18: minimum QoS peak rate - the <param_val> parameter selects the acceptable
value for the peak throughput in range 0-9. The factory-programmed value is 0.
• 19: minimum QoS mean rate - the <param_val> parameter selects the acceptable
value for the mean throughput in range 0-18, 31. The factory-programmed value is 0.
• 20: 3G QoS delivery order - the <param_val> parameter selects the acceptable value
for the delivery order:
o 0 (factory-programmed value): subscribed
o 1: enable
o 2: disable
• 21: 3G QoS erroneous SDU delivery - the <param_val> parameter selects the
acceptable value for the erroneous SDU delivery:
o 0 (factory-programmed value): subscribed
o 1: no detection
o 2: enable
o 3: disable
• 22: 3G QoS extended guaranteed downlink bit rate - <param_val> is the value for the
extended guaranteed downlink bit rate in kb/s. The factory-programmed value is 0.
• 23: 3G QoS extended maximum downlink bit rate - <param_val> is the value for the
extended maximum downlink bit rate in kb/s. The factory-programmed value is 0.