EasyManuals Logo

Windsor Monaco User Manual

Windsor Monaco
318 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #132 background imageLoading...
Page #132 background image
Equipment
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
WINDSOR
5•132
CAUTION: Make sure you have the door keys in your possession
before changing any codes to use in the event you get locked out
of the motorhome.
If the remote does not respond, it may need authorization.
• Locate the keyless entry receiver box behind the instrument cluster.
• Unplug the receiver box. Plug receiver box back in.
• Within three seconds, press the lock button on one remote. The entry
door should lock.
• Press the lock button on the other remote.
The entry door is adjusted at the factory and tested for all operations. The door
incorporates three separate seals to eliminate wind noise during travel.
The door uses two separate locks for safety and security. One locking system
is the door handle and the other is a dead bolt. The door handle incorporates a pri-
mary and secondary latching system. This is used to ensure secure and safe latching.
There are adjustments which can be made to help maintain entry door performance.
Adjusting the Entry Door Latch:
• Determine which bolt needs adjustment.
• Slowly close the entry door observing the latch and strike bolt alignment.
Do not attempt to latch if the alignment is off. If the alignment is correct,
allow the latch to catch in the first (primary) position only.
• The latch should move to the second position with just slight pressure
applied to the entry door. Upper and lower latches should be evenly timed.
Press on the entry door to see if there is any further movement of the door.
• The entry handle should operate with little effort to open the entry door.
An excessive amount of pressure indicates the bolts are set too far back.
• With a 5/8” inch box wrench or socket, loosen the movable strike bolt.
Entry Door
Adjustment
Factory Default Code To Change The Master User Code to PIN
1,3,5 1. Locate and press the Programming Switch located under dash panel.
2. 4 rapid beeps will sound.
3. Enter 1119 on the keypad. 3 rapid beeps will sound.
4. Enter your new PIN, 3-8 digits within 5 seconds.
5. Wait 5 seconds for 2 rapid beeps.
6. Test PIN. If PIN does not work, repeat steps.
Factory Optional User Codes To Change Optional User Code To PIN
1st. 111 1. Lock with code 559 on keypad. Enter master PIN on keypad
2nd. 113 2. Enter factory Optional User Code (etc. #111), 3 beeps will sound.
3rd. 115 3. Enter new Optional User PIN 3-8 digits within 5 seconds, 3 beeps will sound.
4th. 117 4. Wait 5 seconds for 2 rapid beeps.
5th. 119 5. Test Optional User PIN. If PIN does not work, repeat steps.
To Delete an Optional User Code or PIN
1. Lock with code 559 on keypad. Enter master PIN on keypad
2. Enter factory Optional User Code or PIN, 3 beeps will sound.
3. Wait 5 seconds for 2 Rapid Beeps
4. Test deleted code or PIN. If code or PIN still work, repeat steps.
Programming a
Personal Number
To Authorize The
Remote

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Windsor Monaco and is the answer not in the manual?

Windsor Monaco Specifications

General IconGeneral
Fuel TypeGasoline
GPS NavigationOptional
WiFiOptional
Solar PanelOptional
ChassisFord
Sleeping Capacity4
HeatingForced-air furnace
Refrigerator2-way
Stove3-burner
MicrowaveYes
Audio SystemAM/FM/CD/DVD
ShowerYes
SinkYes
FlooringVinyl
SteeringPower steering
Seatbelts4
AirbagsDriver and passenger
BatteriesTwo house batteries
Air ConditioningRoof-mounted
FurnitureDinette, sofa
BluetoothOptional
Warranty1-year limited